Weld Automation Equipment,
Welding Fixtures, Circumferential Welders, Weld Controls
We Have a Large Selection of Welding Automation
Equipment and
Welding Fixtures. Circumferential Welders, Lathes, Weld Monitors,
Used Automatic Welding Controls,
Arc Welding Oscillators.
Welding positioning equipment including,
carriage controls, automated arc welding systems and used
welding equipment and machinery.
1 ea WS704015 Hobart Manipulator / Positioner TIG Welding System. Includes
a 1,500 lb capacity @ 4" C.G. positioner with power tilt and
variable speed rotation. Positioner is mounted on a manual travel car
with 2’ travel. Manipulator has powered lift from 30" to
90", manual reach from 35" to 59" from the center of the
mast. And a 6" horizontal adjuster. Current welding equipment
includes a Jetline model ALC- 401-6 Arc Length control and model 9629
controller and a Jetline CWF-10A cold wire feeder. All equipment mounted
into a single skid frame base. Serial #41-1641. Very Good Condition
1 ea WS703010 Cissel 12’ x 4’ Submerged Arc Welding Gantry. 12’
variable speed rack and pinion driven carriage. 4’ variable speed
Lincoln TC-3 carriage on the cross boom. Complete Lincoln NA-5 sub arc
package. Serial #111978 Good Condition
1 ea WS702002 Weldlogic Positioner/Tig Welding System. A
Weldlogic 200 lb capacity positioner with a 12" capacity chuck
integrated with a Weldlogic complete GTAW welding system. Welding system
includes a Weldlogic RPW-2000 power supply, Weldlogic cold wire feeder,
Weldlogic arc length control, Weldlogic weld oscillator and pendant
control for programming all functions. 230 volt. Serial #9914760 Good
Condition
1 ea WS702003 Weldlogic Positioner/Tig Welding System. A
Weldlogic 200 lb capacity positioner with a 12" capacity chuck
integrated with a Weldlogic complete GTAW welding system. Welding system
includes a Weldlogic RPW-2000 power supply, Weldlogic cold wire feeder,
Weldlogic arc length control, Weldlogic weld oscillator and pendant
control for programming all functions. 230 volt. Serial #9730194 Good
Condition .
1 ea WS604010 "1996" Weldline / Miller GTAW
Circular Welding Station. Weldline Automation Model WA-2 200 lb
Capacity Positioner with a ½" to 16" Capacity 3-Jaw Chuck,
Weldline 6" Arc Length Control, Weldline Weld Sequence Control,
Weldline Cold Wire Feeder, 4" Manual Cross Slide and Rotary Slide.
Pneumatic part Clamping. Welding equipment Includes a Miller XMT-304
Inverter Power Supply, Miller HF-251D-1 High Frequency Arc Starter,
Miller PC-300 Pulse Control, Tweco TC900 Water Circulator and a
Weldcraft WP-27 500 amp Water Cooled Tig Torch. Serial # N/A Good
Condition
1 ea WS603001 Pandjiris Model WHM Welding Gantry Side Beam. A
L-Tec 10’ Powered Elevation Side Beam Mounted on a 67" Pandjiris
Variable Speed Gantry that Runs on 69-1/2" Gauge Rail (Rail Not
Included). Powered Elevation from 17" to 57" to the Bottom
of the Beam. L-Tec Model OM-48 Rack and Pinion Drive Variable Speed
Carriage with Rotary Slide, 6" Vertical and 6" Horizontal
Slides, Carriage Control, UEC-8 Weld Control and EH-11 Weld Head. Serial
#25-1240 Good Condition
1 ea WS601002 Arc Systems Automatic Pipe Welding System. System
Includes a Preston-Eastin HS-2S 2,000 lb Capacity @ 6" C.G.
Headstock with a 20" Diameter Scroll Chuck that has a 6-1/2"
Thru Hole. A Weldlogic AWS-150 Advanced Tig Welding System that
Includes Controls for Variable Speed Rotation of Headstock, Weld Current
Control, Arc Distance Control, Cold Wire Speed Control and Feeder and a
1.0 to 150 amp DC Power Supply. 3 eacg 6" Manual Slides for 3 Axis
Adjustment of Torches. All Controls are Mounted in a Single Remote
Pendant Control. 230/460 Volt. Serial #HS2S-13 Good Condition
1 ea WS509001 Pandjiris "1998" Hot Wire Tig Pipe Welding
Station. A Complete Hot Wire Tig Pipe Welding Station that Includes
a Pandjiris 4’ x 4’ Manipulator on Travel Car, 2 each Pandjiris
HS-20PE-VS Headstocks with TJ-20 Chucks, Pandjiris Pipe Supports on
Manual Travel Cars, Miller / Jetline Welding Package and a Complete set
of 50’ Tracks. Please Ask for a Detailed Specification Sheet.
Excellent Condition
1 ea WS509002 Pandjiris Mig Pipe Welding Station. A Complete
Mig Pipe Welding Station that Includes a Pandjiris 4’ x 4’
Manipulator on Travel Car, 2 each Pandjiris HS-20PE-VS Headstocks with
TJ-20 Chucks, Pandjiris Pipe Supports on Manual Travel Cars, Miller Mig
Welding Package and a Complete set of 50’ Tracks. Please Ask for a
Detailed Specification Sheet. Very Good Condition!
1 ea WS507001 Mark Five Manipulator/Turntable System. Turntable
: 1,000 lb Capacity, 20" High. 24" Diameter Table with Slots.
Variable Speed Drive from .01 to 1.4 RPM. The Manipulator if Fixed Over
the Turntable with a Manual Lift of 30" and a Manual Reach of
24". Serial #JN-1189 Good Condition
1 ea WS404001 Ransome Positioner / Manipulator / Sub-Arc Welding
System. System Includes a Ransome 5P 500 lb Cap. @ 6" C.G.
Positioner (Ser. #1314851) with Power Tilt, Variable Speed Rotation and
Manual Height Adjustment. A 3JC40 40" Diameter 3-Jaw,
Self-Centering Welding Chuck. A Ransome Model 99 Manipulator (Ser.
#9526562) with 72" Power Elevation from 0 to 71" at the Torch,
Fixed Boom with a Manual Spotting Car from 44" to 88" from
Center of the Mast, Manual Mast Rotation. A Complete Lincoln DC-600
Sub-Arc System with NA-5 Control, Weld Head And A Invincible Flux
Recovery System. Very Good Condition
1 ea S412001 Cecil Peck "Dual Position" Outside Corner
Seam Welder. This Machine was Used to Tig Weld the Outside Corners
of Aluminum, Steel and Stainless Electric Panel Boxes. The Dual Operator
Positions were Used for Weld Lengths up to 17" Long. The Air
Clamping Device and Copper Mandrel Plates Could be Increased
(Within Reason) for Longer Welds. The Torch Carriers are Heavy Duty
Variable Speed Devices that are ½ H.P. Dc Motors & Drives. Reconditioned
with 2 Cold Wire Feeders or Converted to Mig Welding Including
Power Sources
1 ea WS406001 Pandjiris Model SWPT-102 Dual Side Beam Stiffener
Welder. HD Welding Carriage, variable speed (0 – 200 IPM). Twin
Cyclomatic Seam Tracking systems to locate torches on opposing sides of
stiffener. Open-End Gantry Style Yoke with 96" of Weld Length
allows loading of stiffener from one end. Advancement of sheet is
readily done with help from pneumatic plate lift rollers that
automatically lift part off back-up bar between welds. 15 Pneumatic hold
down Clamps and Part Locators designed to automatically locate and hold
"I" or "U" shape stiffener in place on sheet. No
tooling or jigs necessary for part alignment. Back-up Bar for heat sink
and part distortion control. System is capable of feeding Aluminum or
Steel Wire using GMAW Process. Twin 180 degree water-cooled GMAW torches
for high production. Remote Control Podium. Was used for welding
stiffeners for aluminum dump truck beds and bodies. Very unique piece of
equipment – Must See!!! Very Good Condition
1 ea WS411001 Linde PTA Surfacing System / 5 x 6 Manipulator. A
Complete Linde Plasma Transfer Arc Weld Surfacing System that Includes a
C75-500 (500 amp, 60% Duty Cycle) Power Supply, PTA Gun, Automatic
Powder Feeder, 12" Manual Vertical Adjuster, and a Linde Solid
State Weld Oscillator. Gun, Vertical Adjuster, Powder Feeder and
Oscillator are Mounted on a Linde OM-48 Variable Speed Travel Car that
Runs on a Fixed Boom Manipulator with 6’ of Horizontal Travel and
60" of Vertical Travel from 31" to 91" by a Screw Driven
Manual Hand Wheel Lift. Good Working Condition
1 ea WS404007P Aronson/Jetline Manipulator/Positioner/Dabber
Welding System. A Complete System That Includes an Aronson Model
G6MR6ML-PK 6' x 6' Manipulator (Serial #73151) with 6' Variable
Speed Reach fron 14" to 86" from the Center of The Mast
Rotation, 6' Constant Speed Lift from 29" to 101" to the
Bottom of the Boom. 111.5" Overall Height. Manual Mast Rotation.
Mounted on a 72" Portable "X" Frame Base. The Welding
Equipment Mounted on the Manipulator Includes a Jetline ALC101-V6T
6" Arc Length Control, a Jetline 9029 Cold Wire Feeder Control, a
9033 Wire Pulse Control and a Jetline Mechanical Dabber System. Welding
Heads are Mounted on a 30" Extension which has a Manual 180 Degree
Vertical and Horizontal Angle Adjuster. Welding Equipment Mounts Over
the Top of an Aronson Model D5-GP100 Positioner (Serial #72299)
825 lb Capacity @ 6" C.G., Manual Tilt, Variable Speed Rotation,
31" Round Table With Slots at a Fixed Height of 31". All
Equipment Calibrated in February, 2003 Good Condition
1 ea WS408001 Compak-o-Matic Rotary Welding Station. System
Includes a Ransome B-100, 100 lb Capacity Welding Positioner, A
Compak-o-Matic PC-300, 300 amp CV Power Supply, a Model 320 Wire Feed
System with a Machine Torch, 8" Horizontal and Vertical Torch
Adjusters, and Model 263 Control Module with Weld Time Function. Serial
#1530 Good Condition
1 ea WS412001 Jetline Portable Heavy Duty Cast Long Length
"Stellite" Overlay System. Jetline TKK-24 Precision Screw
Drive (1-1/2" screw) Side Beam with 24" Travel. Heavy Duty
9-1/2" Power Vertical Slide, 8" of Z axis Manual Slide. Long
Rod Feeder with adj. dia. guide. Miller Oscillator with Center Line
Steering. Overall dimensions of Portable side Beam Assy.76" high,
63" wide, 60" long. System includes Miller 300 amp Synchrowave
welder and Tig Torch. Excellent Condition
1 ea WS404002 Ransome/Lincoln Gear/Flange Welding System. System
Includes a Ransome Model 25P-A, 2,500 lb Cap. @ 6" C.G., Power
Tilt, VS Rotation from .038 to 1.55 RPM, Manual Elevation from
34.5" to 58.5" in 6" Increments, Ser. #1630532. System
also Includes a Lincoln DC-600 Power Supply with a NA-5 Control and a
NA-5R Mig Welding Head. Mig Gun Mounts on a Air Actuated Pivot that also
Carries a Welding Shield into Place. A Fully Automatic System for
Welding of Gears or Pipe Flanges. Good Condition
1 ea WS205001 Jetline Pipe Welding System. This System was
Manufactured by Jetline Engineering in 1996 for the Joining of
Straight Lengths of Pipe. System Includes a Jetline 4' Side Beam
with Carriage (Ser.#968352), Jetline 9500 Systems Controller
(Ser.#965865), Jetline 9200 Oscillator with Joy Stick Positioning
Pendant, Jetline 9032-39620 Oscillating Program Controller
(Ser.#968352), Miller Maxtron 450 amp Welding Power Supply
(Ser.#KG061047) , Miller A-1D4 Automatic Wire Feed Head, and Rotary
Slide all Mounted on a Variable Speed Travel Car with 60' of Inverted
Angle Iron Track. (Ser.#686160). Very Good Condition
1 ea WS999001 Linde/Jetline HWC-7 Cold Wire Tig System. Jetline
ZB-100 Positioner on moveable screw drive base. Complete with HW-500SS
Welder, Auto Controls, Cross Slides and Floor Standing Base. Excellent
Condition
1 ea WS006003 Hobart/Aronson 2 Station Automatic Spud Welder. Mig
Welds Rings up to 12" Diameter, Two alternate weld stations w/ Air
Clamping of parts. Control Console w/ Station Selection. Many Tooling
Fixtures. Var. Speed Rot. by 2 Aronson positioners. Includes Hobart Dual
Wire Feeder, Torches and Welder. Complete System Ready to Weld
Robotic Welding Cells
1 ea RC505001 "2003" Panasonic 3 Axis Model ISP
Cartesian Robotic Tig Welding Cell. Initially powered up in November
2003 this cell was used off and on for approximately 8 months before the
application was discontinued. This Panasonic Model ISP Cartesian Robot,
has approx. 43" (x) horizontal movement, 15" (y) vertical
movement and 21" (z) horizontal movement. There is also a 2 axis
clamping fixture or tooling table. The complete welding package on this
cell includes Two (2) Water Cooled Tig Torches with manual adjustable
separation of the torch holders on one axis, Two (2) Panasonic YC-500WX4
Power Supplies completely integrated with all regulators, hoses, cables
etc. Water supply required. The welding cell is 75" wide x
103" high x 145" deep and has a complete safety package
including, Powered Safety Screen, Light Package, Front Operating Control
and Palm Buttons. This cell could be changed to the Mig welding
process. This is a late model, low hour, system in Excellent Condition
1 ea RC505002 "2003" Panasonic 4 Axis Model ISP
Cartesian Robotic Tig Welding Cell. Initially powered up in November
2003 this cell was used off and on for approximately 8 months before the
application was discontinued. This Panasonic Model ISP Cartesian Robot,
has approx. 17 1/2" (x) horizontal movement, 10" (y) vertical
movement and 15" (z) horizontal movement. The Fourth Axis is a
Rotating Wrist movement for the Torch Holding Device. This Cell also
includes a Horizontal Moving Fixture/Tooling Table Integrated with the
Robot from the Load/Unload position to the Robotic Welding Position. The
Complete Welding Package on this cell includes one (1) Panasonic
YC-300WX4 Power Supply and One (1) Water Cooled Tig Torch completely
integrated with all cables, hoses, etc. Water supply required. The
welding cell is 75" wide x 103" high x 126" deep and has
a complete safety package including, Powered Safety Screen, Light
Package, Front Operating Control and Palm Buttons. This cell could be
changed to the Mig welding process. This is a current model, low hour,
system in Excellent Condition!
1 ea RC505005 "2003" Panasonic VR-008 GII Robotic, 6
Axis Tig Welding Cell. This is a larger, panel constructed, Robotic
welding Cell with a large Fixture/Tooling table that has approx.
78" of in and out movement between load and welding stations. The
Complete Welding Package on this cell includes one (1) Panasonic
YC-300WX4 Power Supply, One (1) Water Cooled Tig Torch complete with all
cables, hoses, etc. Water supply required. This Welding Cell accomodated
this Panasonic VR-008 GII Robotic System and the "2003"
Motoman UP-50 listed and priced separately below. See the picture of
this larger panel constructed cell for approximation of size. This is
a Current Model, Low Hour System, in Excellent Condition! Price includes
Panel Constructed Cell.
1 ea RC505004 "2003" Panasonic Robotic VR-008 GII, 6
Axis Tig Welding Cell. The Fixture/Tooling Platform is on an Integrated
Horizontal Travel Part Presentation Carriage with 26" of Movement
from the Load/Unload Station. This system provides maximum operator
access for load/unloading and increased productivity. The Complete
Welding Package on this cell includes one (1) Panasonic YC-300WX4 Power
Supply, One (1) Water Cooled Tig Torch complete with all cables, hoses,
etc. Water supply required. The welding cell is a completely enclosed
102" wide x 103" high x 172" deep structure with side
access doors and a complete safety package including, Powered Safety
Screen, Light Package, Front Operating Control and Palm Buttons. This
is a Current Model, Low Hour System, in Excellent Condition!
1 ea R510001P Motoman Model YRFL-NND10G 6-Axis Robot. 22 lb
Payload Capacity. Robot Controller NOT Included. "1986" Serial
#RH9963-6047-8 "As-Is" Only
1 ea R510011P Miller/OTC Model MRV-6 6-Axis Welding Robot. 13.2
lb Payload Capacity. 55.2" Reach. Includes a Miller Model C-1
Control Cabinet. Welding Equipment NOT Included. "1991".
190-575 Volt. Serial #KB168739 "As-Is" Only
1 ea R510012P Miller/OTC Model MRV-6 6-Axis Welding Robot. 13.2
lb Payload Capacity. 55.2" Reach. Includes a Miller Model C-1
Control Cabinet. Welding Equipment NOT Included. "1992".
190-575 Volt. Serial #KC301838 "As-Is" Only
1 ea WS605013P Cybotech Automatic Manipulator / Positioner Tig
Welding System. System Includes A Fabspec 2,500 lb Capacity
Positioner, a 6 Axis Cybotech 4’ X 3’ Manipulator / 6’ Travel Car,
Cybotech RC-6 Controller, Cold Wire Feeder, Miller Syncrowave 300 w/
SP-4 Pulser. System Offers 9 Axis of Powered Movement. Good Condition
1 ea WS605014P Cybotech Automatic Manipulator / Positioner Tig
Welding System. System Includes A Fabspec Model 1840 2,000 lb
Positioner, a 6 Axis Cybotech 4’ X 3’ Manipulator / 6’ Travel Car,
Cybotech RC-6 Controller, Cold Wire Feeder, Cybotech EPU Power Supply.
System Offers 9 Axis of Powered Movement. Good Condition
WELDING LATHES
1 ea L604009 Custom 12" GTAW Welding Lathe. 6"-12"
Part Length Capacity. 9" Maximum Diameter Capacity. 6" Stroke
Pneumatic Tailstock. 5" Pneumatic Torch Lifter. All Functions
Controlled by an Allen-Bradley SLC-500 Programmable PLC. Rotary Ground.
Welding Equipment Includes a Powcon 150STP Power Supply and a 120 amp
Air Cooled Tig Torch. Serial # N/A Good Condition
1 ea L608004 Jetline 14" x 14" Mig Welding Lathe. 14"
Part Diameter Capacity. 14" Length Capacity. Jetline ZB-100
Positioner, 100 lb Weight Capacity. Air Actuated Tail Stock for Part
Clamping. Vertical, Horizontal and Rotary Cross Slides. Miller 300 amp
Power Supply. 230/460 Volt. Serial #910424 Good Condition
1 ea L601001 Jetline Model CWP-24 90 Degree Power Tilting Lathe
Bed. 200 lb Weight Capacity. 20.5" Length Capacity. 12"
Diameter Capacity. For use as a Vertical or Horizontal Welding Lathe
with a 90 Degree Powered Tilting Bed. 8" Capacity Chuck with a
1/2" thru hole for back purging. 3" Air Actuated Tailstock for
Part Clamping. Jetline ALC101-V4T Arc Length Controller. Jetline Model
9024-101 Circumferential Tig Weld Sequencer. Variable Speed Torch
Carriage for Either Circumferential or Longitudinal Welding.
Powered Torch Lifter. Powered Slides. 115 volt. Serial #920131 Good
Condition
1 ea L611014 Jetline Model CWP-24 90 Degree Power Tilting Lathe
Bed. 200 lb Weight Capacity. 20.5" Length Capacity. 12"
Diameter Capacity. For use as a Vertical or Horizontal Welding Lathe
with a 90 Degree Powered Tilting Bed. 8" Capacity Chuck with a
1/2" thru hole for back purging. 3" Air Actuated Tailstock for
Part Clamping. Jetline ALC201-V4T Arc Length Controller. Jetline Model
9500 Weld Sequence Control. Jetline CWF-10A Cold Wire Feeder. Variable
Speed Torch Carriage for Either Circumferential or Longitudinal
Welding. 115 volt. Serial #969257 Good Condition
1 ea L601011P Bancroft Model 1210 "Twin Torch" Welding
Lathe. 1,000 lb Load Capacity. 72" Length Capacity. 12"
Swing Capacity. 6" Pneumatic Tailstock with 650 lbs Clamping Force.
Variable Speed Rotation from 0.5 to 10 RPM by a 10 turn Potentiometer.
Weld Overlap Timer. System Includes 2 each Manual Spotting Cars each
with Air torch Lifters, Bancroft Wire Feeder, Rotary Slide,
4"Manual Cross Seam Adjusters, Mig Gun and Linde VI-400 Power
Supplies. Dual 500 AMP Rotary Grounds. 230/460 Volt Serial
#3100-50205-01Good Condition
1 ea L501001 WeldLogic CWT-12-15 GTAW Welding Lathe System.
CWT-12-15 Variable Speed Headstock with Pneumatic Tailstock, 4"
stroke. Arc Length Controlled Vertical Slide. 6" 3-Jaw
Self-Centering Chuck. Pneumatic Torch Retract (to rear). Manual Vertical
Slide w/ 10" of Adjustment. Manual Rotary Slide for Torch Angle
Adjustment. Cold Wire Feeder and Mini Wire Delivery Guide. WP-22
Automatic Tig Torch. Max Part Length – 15", Max Part Diameter
– 10-1/2". Serial #9413-014 Very Good Condition
1 ea L512002 Bancroft High Capacity 3 Station, Dual Torch,
Indexing Welding Lathe. 23" Length Capacity, 12" Diameter
Capacity. 3 Position Indexing Turret for Loading of Parts, Welding of
Parts and Cooling of Parts. 2 Torches for Welding on both Ends of Parts.
GMAW Welding Equipment Includes 2 each Miller S-62 Wire Feeders with
Tweco Water Cooled Auto Guns on 4" Bancroft Retractable Air Slides.
Serial #3327/109-843 Good Condition
1 ea L305001 Bancroft Model VH-24 Welding Lathe. 33" Long
x 48" Diameter Capacity. Pneumatic Torch Lifter, Forward and
Reverse Variable Speed, Weld Overlap Timer and a Miller 60M Control and
Feed Head Serial #3609-(117-212) Good Condition
1 ea L305002 Bancroft Model VH-24 Welding Lathe. 33" Long
x 48" Diameter Capacity. Pneumatic Torch Lifter, Forward and
Reverse Variable Speed, Weld Overlap Timer and a Miller 60M Control and
Feed Head Serial #3610-(117-213) Good Condition
1 ea L206001P Stoody Screw Flight Tig Hard Surfacing Lathe. Capacity
of 7" Diameter (may be increased) x 144" Long. This Machine
was used for Hard Surfacing with #6 CoCrA Solid Lengths. Has Oscillating
Head, Preheat System, Control Console and 500 amp Miller DC Power
Supply. Just Out of Service, Good Operating Condition!
1 ea L412002 Ransome/Weldwire 2,000 lb Tilting Welding Lathe Bed. 2,000
lb Capacity Headstock @ 6" C.G. Mounted on a 20 Degree Power
Tilting Bed in Either Direction. 27" Diameter Swing Capacity.
Out Board Roller Support Wheels that Manually Adjusts from 22" to
60" from the Face of the Chuck. 20" Diameter 3-Jaw Self
Centering Chuck with a 7-1/2" Diameter Thru Hole. Variable Speed
Rotation by a 10 Turn Potentiometer. Pendant Control for all Functions.
230/460 Volt. Serial #N/A Very Good Condition
1 ea L9912001 Bancroft Welding Lathe. Work Piece Capacity
24" X 72". Bed 12’ Overall, Tailstock has Air Cylinder for
part clamping. Linde Automatic Head w/Cross Slides. Variable Speed
Rotation For/Rev. As-Is
1 ea L610002 Jetline Model CWL-72 Lathe and 13’ Side Beam. 500
lb Capacity Variable Speed Headstock / Tailstock. 30" diameter
Capacity. 72" Length Capacity (Can Increased to 48" -
120" Capacity with a Spacer). 13’ Side Beam with a Manual
Spotting Car that has 12’6" of Travel. Welding Equipment Includes
a Jetline Model 9500 System Control, ALC-201V6E ArcLength Control,
Rotary Slide and Horizontal Slide. Serial #81322 Good Condition
1 ea L1054413 Melton Model 6330 Single Torch Welding Lathe. Capacity30"
dia. X 37" long. Programmable A.B. SLC 500 Control. Pneumatic
Fixture Clamping. Miller Maxtron 450 Pulse Welding System with Automatic
1DA Control & Head. Welding system completely integrated. Safety
Light Curtain, Operator Console w/Palm Buttons. Automatic Leather
Curtains. Hood for exhaust. Complete, ready for your fixturing. "1993"
Very Good Condition
1 ea L504001 Custom Built Lathe Type Welding Fixture.
Estimated weight capacity 350 lbs. Swing Dia. 48", Tailstock is
Power Driven on a Lead Screw to increase the available part length from
approx. min. of 19’’ to max. of 60". Variable Speed Rotation by
DC Drive with Manual Shift Transmission for Three forward Speed Range
and One Reverse. Rotating Welding Ground included. As Is in Working
Order
1 ea L610001P Cecil Peck 12’ Welding Lathe. 1,000 lb
Weight Capacity. 32" Diameter Capacity. 12’ Maximum Length
Capacity. Air actuated Tailstock. Linde Model OM-48 Variable Speed
Carriage. Step Over Control. 600 amp Rotary Ground. Through Hole Purge
on Tailstock Face Plate. Welding Equipment NOT Included. Serial #N/A Good
Condition
1 ea L502001 Centurion Model WL24X168 Welding Lathe. 24"
Diameter Capacity. 168" Length Capacity. Variable Speed Travel Car
and a Manual Spotting Car. Pandjiris Model "A" 31-1/4"
Capacity "Gripper" Chuck. Manual Tailstock Mounted on a
Powered Travel Car. Powered Elevation Side Beam. Includes a Lincoln
DC-600 Power Supply with a NA-3N Sub-Arc System. Good Condition
Automation Welding Equipment
