New and Used Welding Equipment Inventory, Weld Plus Inc

Any MBC BP 2A "NEW" M.B.C. Model BP-2-A, 200 lb Bench Top Positioners. 0-4.5 RPM Capacity 200 lbs balanced load in the horizontal position, 100 lbs in the vertical. 12" dia. slotted faceplate. Variable Speed Rotation, H.F. Protected, On/off Foot Switch, Manual Hand wheel Tilt, 115 volt. Available with 3-Jaw 9" Quick Lever Chuck. "New"

Any MBC BP 2B "NEW" M.B.C. Model BP-2-B, 200 lb Bench Top Positioners. 0-9 RPM Capacity 200 lbs balanced load in the horizontal position, 100 lbs in the vertical. 12" dia. slotted faceplate. Variable Speed Rotation, H.F. Protected, On/off Foot Switch, Manual Hand wheel Tilt, 115 volt. "New"

Any MBC BP SB "NEW" M.B.C. Model BP-SB, 100 lb Bench Top Positioners. 0-18 RPM Capacity 100 lbs balanced load in the horizontal position, 50 lbs in the vertical. 12" dia. slotted faceplate. Variable Speed Rotation, H.F. Protected, On/off Foot Switch, Manual Hand wheel Tilt, 115 volt. "New"

Any MBC R2 Model R2, 200 lb Bench Top Positioners with a 2" thru hole design with optional AGP- 2 Through Hole Purge. These are "New" welding positioner in stock. Capacity 200 lbs balanced load with the part in the horizontal position, table vertical. 100 lbs with the part in the vertical position weld table flat. 13" dia. slotted faceplate 5/16th thick with 2" thru hole. Variable Speed Rotation 0-6 RPM, 102 in lb torque, H.F. Protected, On/off Foot Switch, Manual Hand wheel Tilt, 115 volt. "New"

Any PRO WP250 "New" Profax 250 lb Positioner. 250 lb Capacity @ 4" C.G., 0 to 90 Degree Manual Hand Wheel Tilt. Variable Speed Rotation from 0.0 to 5.5 RPM. 13.75" Diameter Table with Slots and a 1" Diameter Thru Hole. High Frequency Protected. On/Off Foot Pedal. 115 Volt Brand New – Ready to Ship !!

PAN MP “NEW” Pandjiris Mini Pro 350 lb Bench Top Positioner. 350 lb Horizontal Capacity, 350 lb Vertical Capacity. Variable Speed from .37 to 13.0 RPM. 0 to 90 Degree Manual Pin Lock Tilt in 15 Degree Increments. 8” Diameter 3-Jaw Self Centering Chuck with a 2.5” Thru Hole. On/Off Foot Switch. 115 Volt. Shipping weight 105 lbs. Brand New – Ready to Ship

Any PRO WP500 "NEW" Profax 500 lb Positioner. 500 lb Capacity @ 6" C.G., 135 Degree Power Tilt. Variable Speed Rotation from 0.4 to 4.0 RPM. Fixed Table of 25.25". 19.5" Round Table with Slots. 300 Amp Rotary Ground Forward/Reverse Momentary Foot Pedal. 115 Volt Brand New – Ready to Ship

IRC 750 4FB “NEW” Irco Automation 750 lb Positioner. 750 lb capacity @4” c.g., 135 degree power tilt. .01 to 4.8 variable speed rotation. 21.5” fixed table height. 22” square table with slots. 400 amp copper rotary ground. Pendant control. On/Off foot pedal. 115 volt. Shipping weight 390 lbs. NEW !!! – In Stock

Any PRO WP1000 "NEW" Profax 1,000 lb Positioner. 1,000 lb Capacity @ 6" C.G., 135 Degree Power Tilt. Variable Speed Rotation from 0.2 to 2.0 RPM. Fixed Table of 33.75". 24.5" Round Table with Slots. 500 Amp Rotary Ground Forward/Reverse Momentary Foot Pedal. 115 Volt Brand New – Ready to Ship!

Any IRC 15 4AB "NEW" Irco Automation 1,500 lb Positioner. 1,500 lb capacity @ 4" c.g., 135 degree power tilt. .06 to 3.0 variable speed rotation. Manual adjustable table height from 23" to 37" in 7" increments. 24" octagon table with slots. 400 amp copper rotary ground. Pendant control. On/off foot pedal. 115 volt. NEW !

Any PAN 15 4FB "NEW" Pandjiris 1,500 lb Positioner. 1,500 lb Capacity @ 4" C.G., 135 degree Manual Hand Wheel Tilt, Variable Speed Rotation from .08 to 1.60 RPM. 23-1/4" Fixed Table Height. 24" Square Table with Slots. 25' Pendant Control. 115 Volt. PROUDLY MADE IN THE U.S.A. NEW !!

Any PAN 15 4AB "NEW" Pandjiris 1,500 lb Positioner. 1,500 lb Capacity @ 4" C.G., 135 Degree Constant Speed Power Tilt, Variable Speed Rotation from .08 to 1.60 RPM. Manual Adjustable Table Height from 23-1/2" to 37-1/2" in 7" Increments. 24" Square Table with Slots. 25' Pendant Control. 115 Volt

Any PAN 30 6FB "NEW" Pandjiris 3,000 lb Positioner. 3,000 lb Capacity @ 6" C.G.., 135 Degree Constant Speed Power Tilt, Variable Speed Rotation from .07 to 1.40 RPM. 32-5/8" Fixed Table Height. 30" Square Table with Slots. 25' Pendant Control. 460 Volt in stock. 230 volt available on request. PROUDLY MADE IN THE U.S.A.

Any PAN 30 6AB "NEW" Pandjiris 3,000 lb Positioner. 3,000 lb Capacity @ 6" C.G., 135 Degree Constant Speed Power Tilt, Variable Speed Rotation from .07 to 1.40 RPM. Manual Adjustable Height from 33" to 53" in 4" Increments. 30" Square Table with Slots. 25' Pendant Control. 460 Volt in stock. 230 volt available on request.

Any GEN PT1500V "NEW" Gentec Model PT-1500V 3,300 lb Positioner. 3,300 lb Capacity @ 15" C.G., 135 degree power tilt, Variable speed rotation from 0.1 to 1.0 RPM. Fixed height of 39" With the table flat. 31" diameter round table with mounting slots. 800 amp grounding capacity. Hand pendant control. On/Off foot control. 230/460 volt

Any PAN 45 12AB "NEW" Pandjiris 4,500 lb Positioner. 4,500 lb Capacity @ 12" C.G., 135 Degree Constant Speed Power Tilt, Variable Speed Rotation from .03 to .97 RPM. Manual Adjustable Height from 39" to 57" in 4-1/2" Increments. 48" Square Table with Slots. 25' Pendant Control. 230 or 460 Volt PROUDLY MADE IN THE U.S.A. NEW !

IRC 45 12AB “NEW” Irco Automation 4,500 lb Positioner. 4,500 lb capacity @ 12” c.g., 135 degree power tilt. .03 to 1.2 variable speed rotation. Manual adjustable table height from 40” to 56” in 4” increments. 42” square table with slots. 600 amp copper rotary ground. Pendant control. On/Off foot pedal. 460 volt. Shipping weight 2,850 lbs

Any ARO HD45 "NEW" Koike-Aronson Model HD-45 4,500 lb Positioner. 4,500 lb capacity @ 12" C.G., 135 degree constant speed power tilt, Variable speed rotation from .04 to 1.2 RPM, Manual adjustable table height from 34.5" to 54.5" in 5" increments. 36" square table with slots. Pendant control for all functions.460 volt,3-phase. NEW!! -In Stock

Any ARO HD60 "NEW" Koike-Aronson Model HD-60 6,000 lb Positioner. 6,000 lb capacity @ 12" C.G., 135 degree constant speed power tilt, Variable speed rotation from .05 to 1.5 RPM, Manual adjustable table height from 44.5" to 74.5" in 6" increments. 48" square table with slots. Pendant control for all functions. 460 volt,3-phase. NEW!!! -In Stock

Any GEN PT3000 "NEW" Gentec Model PT-3000 6,600 lb Positioner. 6,600 lb Capacity @ 11.8" C.G.. 135 Degree Power Tilt, Variable Speed Rotation from 0.1 to 1.0 RPM. Fixed Height of 43" with the Table Flat. 39" Round Table with Mounting Slots. 800 amp Grounding Capacity. Hand Pendant Control. On/Off Foot Control. 230/460 Volt 3 Phase. NEW in Stock!! Ready to Ship

Any ARO HD100 "NEW" Koike-Aronson Model HD-100 10,000 lb Positioner. 10,000 lb capacity @ 12" C.G., 135 degree constant speed power tilt, Variable speed rotation from .04 to 1.0 RPM, Manual adjustable table height from 44.5" to 66.5" in 6" increments. 48" square table with slots. Pendant control for all functions.460 volt,3-phase. NEW!!! - In Stock

Any GEN PT5000 "NEW" Gentec Model PT-5000 11,000 lb Positioner. 11,000 lb Capacity @ 11.8" C.G.. 135 Degree Power Tilt, Variable Speed Rotation from 0.04 to 0.8 RPM. Fixed Height of 47" with the Table Flat. 47" Round Table with Mounting Slots. 800 amp Grounding Capacity. Hand Pendant Control. On/Off Foot Control. 230/460 Volt 3 Phase. NEW in Stock!! Ready to Ship

Any IRC 3JC20 NEW Model 3JC20 Quickset Pipe Chuck. Clamping Diameter. Outside 5/8" to 15-1/2", Inside Clamp. 5" to 20", Quick-Set of 3-Jaws w/Pins. Mounting not Included NEW !

Any PAN TJ-20 NEW Model TJ-20 Quickset Gripper Chuck. Clamping Diameter. Outside 1" to 16-1/2", Inside Clamp. 6-1/4" to 20", Quick-Set of 3-Jaws w/Pins. Mounting not Included NEW !

Any PAN MOD-A NEW Model "A" Quickset Gripper Chuck. Clamping Diameter. Outside 1-1/2" to 27-5/8", Inside Clamp. 5-1/2" to 31-1/4". Quick-Set of 3-Jaws w/Pins. Mounting Not Included NEW !

Any IRC 3JC33 NEW Model 3JC33 Quickset Pipe Chuck. Clamping Diameter. Outside 5/8" to 28-1/2", Inside Clamp. 5" to 33". Quick-Set of 3-Jaws w/Pins. Mounting Not Included NEW !

Any PAN MOD-B NEW Model "B" Quickset Gripper Chuck. Clamping Diameter. Outside 1-1/2" to 40-3/4", Inside Clamp. 5-1/2" to 44-3/8". Quick-Set of 3 Jaws w/Pins. Mounting Not Included NEW !

Any PAN MOD-B-60 New Model "B-60" Quickset Gripper Chuck. Clamping Diameter. Outside 1-1/2" to 63-7/8". Inside 7" to 68". Quick-Set of 3 Jaws w/Pins. Mounting Not Included. NEW !

P810022 Aronson B-200Bench Mount Manual Positioner. 200 lb capacity @ 12” c.g., 360 degree manual rotation with friction breaking. 360 degree manual tilt with friction breaking. 360 degree manual revolving base. 6” diameter round table. 12.5” height. Serial #93873 Good Condition

1 ea P411006 WMP 300 lb Positioner. 300 lb Load Capacity. Constant Speed Rotation. 90 Degree Manual Tilt. 24" Fixed Height. 18" Diameter Table w/ Slots. On/Off Foot Pedal. 230/460 volt. Serial # N/A As Is Only!! – Good Working Condition

P810013 Aronson AW-300A Positioner. 300 lb capacity @ 12” c.g.. .2 to 6.0 RPM variable speed rotation. 360 degree manual tilt with brake and 45 degree pin lock indexing. 8” diameter round table. Forward/stop/reverse foot pedal. Pendant control. 120 volt. Serial #510-90179
Good Condition

P810014 Aronson AW-300A Positioner. 300 lb capacity @ 12” c.g.. .2 to 6.0 RPM variable speed rotation. 360 degree manual tilt with brake and 45 degree pin lock indexing. 8” diameter round table. Forward/stop/reverse foot pedal. Pendant control. 120 volt. Serial #n/a Good Condition

P810031 Aronson AW-300A Positioner. 300 lb capacity @ 12” c.g.. .2 to 6.0 RPM variable speed rotation. 360 degree manual tilt with brake and 45 degree pin lock indexing. 8” diameter round table. Forward/stop/reverse foot pedal. Pendant control. 120 volt. Serial #n/a Good Condition

1 ea P994007 Standard Machine Co. Positioner. Approx. 400# Capacity Power Hyd. Tilt, Variable Speed Rotation. 13" Dia. Table w/ Slots. Fixed Height of 26" Ctr. line of Rotation. AS IS ONLY

1 ea P407002 Pandjiris Alpha 5-V8 Positioner. 500 lb cap. @ 3" C.G., 90 Degree Manual Tilt with Pin Locks in 12.5 Degree Increments. Variable Speed Rotation from .27 to 6.70 RPM. 20.5" Fixed Height to the Center of the Rotational Axis. 18" Diameter Round Table w/ Slots. On/Off Foot Pedal. Serial #800-2073-2 Good Condition

1 ea P9911008 Aronson BT-500A Welding Positioner. 500 lb Cap. Variable Speed, Manual Side Arm Tilt, 8" Dia. 3-Jaw Chuck, Needs Vert. Mtg. Pipe. Foot Controls, Ser.#77785 Good Condition

P810015 Aronson BT-500 Positioner. 500 lb capacity @ 12” c.g.. .33 to 10.0 variable speed rotation by a Graham drive. 360 degree manual rotation with brake. 6” diameter round table. Forward/stop/reverse foot pedal. 120 volt. Serial #5348 Good Condition

1 ea P205004 Jetline Model ZB-500A Positioner. Capacity of 500 lbs @ 4". Variable Speed Rotation. Manual Hand Wheel Tilt. 24" Diameter Table. Good Condition

1 ea P711002 Ransome Model 5P 500 lb Positioner. 500 lb capacity @ 6" c.g.. Power tilt. Variable speed rotation from .05 to 2.0 RPM. Manual adjustable height from 32.5" to 50.5" in 6" increments. 30" round table with slots. Pendant control for all functions. Forward/Stop/Reverse foot pedal. 460 volt. Serial #138439. Good Condition

1 ea P409001 Ransome/Worthington 5P Positioner. 500 lb Capacity @ 6" C.G., Power Tilt, Variable Speed Rotation from .05 to 2.0 RPM. Manual Adjustable Table Height from 32-1/2" to 50-1/2". On/Off Foot Pedal. Includes a 12" Capacity 3-Jaw Self Centering Chuck. Serial #54055 Good Condition

P904002 Teledyne Readco Model UPC-5 Positioner. 500 lb capacity @ 6" C.G.. Manual hand wheel tilt, Variable speed rotation from .040 to 2.0 RPM. Manual adjustable table height from 25" to 55" in 6" Increments. 26" round table with slots . Pendant control. On/Off Foot Pedal. 115 volt. Serial #15256 Good Condition

1 ea T309002 Kistler / Pandjiris Model U-150 / U-150H Pipe Positioner with Clamping Roller System. 1" - 8" Clamping Range. 660 lb Horizontal Weight Capacity. 330 lb Vertical Weight Capacity. Variable Speed Rotation from 0 to 50 IPM. With Optional #151 Cart and Forward / Stop / Reverse/Variable Speed Rotary Foot Drum Control. An Excellent System for Flange and Elbow Welding on Small Diameter Pipe. 115 Volt. Good Condition.

T809008 Kistler / Pandjiris Model U-150 / U-150H Pipe Rotator with Clamping Roller
System. 1" - 8" Clamping Range. 660 lb Horizontal Weight Capacity. 330 lb Vertical Weight Capacity. Variable Speed Rotation from 0 to 50 IPM. With Optional #151 Cart and Forward / Stop / Reverse/Variable Speed Rotary Foot Drum Control. An Excellent System for Flange and Elbow Welding on Small Diameter Pipe. 115 Volt. Serial #11002. Good Condition

T809009 Kistler / Pandjiris Model U-150 / U-150H Pipe Rotator with Clamping Roller
System. 1" - 8" Clamping Range. 660 lb Horizontal Weight Capacity. 330 lb Vertical Weight Capacity. Variable Speed Rotation from 0 to 50 IPM. With Optional #151 Cart and Forward / Stop / Reverse/Variable Speed Rotary Foot Drum Control. An Excellent System for Flange and Elbow Welding on Small Diameter Pipe. 115 Volt. Serial #11011.Good Condition

T809010 Kistler / Pandjiris Model U-150 / U-150H Pipe Rotator with Clamping Roller
System. 1" - 8" Clamping Range. 660 lb Horizontal Weight Capacity. 330 lb Vertical Weight Capacity. Variable Speed Rotation from 0 to 50 IPM. With Optional #151 Cart and Forward / Stop / Reverse/Variable Speed Rotary Foot Drum Control. An Excellent System for Flange and Elbow Welding on Small Diameter Pipe. 115 Volt. Serial #11013.Good Condition

1 ea P805026P Aronson Model D-10A 1,000 lb Positioner. 1,000 lb capacity @ 4" c.g.. 135 degree power tilt. Variable speed rotation from 0.0 to 3.25 rpm. Manual adjustable height from 17.75" to 32.125" in 7" increments. 24" round table with slots. Pendant control for all functions. 460 volt. Serial #8629-1 Good Condition

1 ea P408001 Teledyne Readco Model UPC-10 Positioner. 1,000 lb Capacity @ 6" C.G.. Power Tilt, Variable Speed Rotation from .040 to 2.0 RPM. Manual Adjustable Table Height from 25" to 49" in 6" Increments. 29" Round Table with Slots. Pendant Control. On/Off Foot Pedal. Serial #104199 Good Condition

1 ea P605016 Teledyne Readco Model UPC-10 Positioner. 1,000 lb Capacity @ 6" C.G.. Power Tilt, Variable Speed Rotation from .040 to 2.0 RPM. Manual Adjustable Table Height from 25" to 49" in 6" Increments. 29" Round Table with Slots. Pendant Control. On/Off Foot Pedal. Serial #104902 Good Condition

1 ea P305001 Ransome SW-10A Twin Axis Positioner. 1,000 lb Capacity @ 6" C.G.. 360 Degree Constant Speed Powered Side Arm Tilt. Variable Speed Rotation from .06 to 2.0 rpm. 36" Diameter Table with Slots. On/off Foot Pedal. 115 Volt. Serial #9321389 Good Condition

1 ea P806002 Aronson Model HD20A-PTVR-2 2,000 lb Positioner. 2,000 lb capacity @ 6" c.g.. 135 degree power tilt. Variable speed rotation from .07 to 2.0 rpm. Manual adjustable table height from 23.75" to 38.75" in 7.5" increments. 24" round table with slots. Pendant control for all functions. 115 volt. Serial #81976 Good Condition

1 ea P806003 Aronson Model HD20A-PTVR-2 2,000 lb Positioner. 2,000 lb capacity @ 6" c.g.. 135 degree power tilt. Variable speed rotation from .07 to 2.0 rpm. Manual adjustable table height from 23.75" to 38.75" in 7.5" increments. 24" round table with slots. Pendant control for all functions. 115 volt. Serial #81985 Good Condition

1 ea P803018 Aronson Model HD-25 2,500 lb Positioner. 2,500 lb capacity @ 6" c.g., Power tilt. Variable speed rotation from .07 to 2.0 rpm. Manual adjustable table height from 34.5" to 56.5" in 5" increments. 30" square table with slots. Pendant control for all functions. Forward / Stop / Reverse Foot Pedal. 230 or 460 volt. Serial # n/a Good Condition

1 ea P510009 Koike-Aronson HS10BBH/T3-30 "Skyhook" Positioner. 2500 lb Load Capacity. Center of Gravity 28". Overhang 3". Off-Center 38" Table. "Skyhook" Positioners Provide Part Rotation in Two 360 Degree Axis which Result in Partial or Full Inverting of the Workpiece. Pendant Control. Serial #80308 Good Condition

1 ea P510010 Koike-Aronson HS10BBH/T3-30 "Skyhook" Positioner. 2500 lb Load Capacity. Center of Gravity 28". Overhang 3". Off-Center 38" Table. "Skyhook" Positioners Provide Part Rotation in Two 360 Degree Axis which Result in Partial or Full Inverting of the Workpiece. Pendant Control. Serial #N/A Good Condition

1 ea P304009 Cullen- Friestadt Model 25, 2500 lb Positioner. 2500 lb cap. @ 6" C.G.. Variable Speed Rotation by Hand Wheel, Power Tilt,. Manual Adjustable Table Height. 30" Square Table Pendant Control for Stop Start. Serial # 1090 In Working Cond. AS IS ONLY

1 ea P410003 Heinrichs Gluck H75 "Powered Elevation" Positioner. 2,500 lb Capacity @ 12" C.G., Power Tilt, Variable Speed Rotation. 40" to 64" Power Elevation. 24: Square Table. On/Off Foot Pedal. Serial #D20062740 Good Condition

1 ea P709005 P & H Model WP-2 2,500 lb Positioner. 2,500 lb capacity @ 6" c.g.. Manual/hydraulic tilt. Variable speed rotation. Manual adjustable height from 24" to 40" in 6" increments. Pendant control. 230/460 volt. Serial #WP-2447. Good Condition

1 ea P609001 Ransome Model 25P Positioner. 2,500 lb Capacity @ 6" C.G., Power Tilt, Variable Speed Rotation from .031 to 2.0 RPM. 40" Square Table. Manual Height Adjustment from 45-1/2" to 57-1/2. Pendant Control. Serial #N/A Good Condition

1 ea P406002 Webb 25P, 2,500 lb Positioner. 2,500 lb Capacity @ 6" C.G., Power Tilt, .15 to 1.5 Variable Speed Rotation. 36" Fixed Table Height. 30" Diameter Round Table with Slots. Pendant Control. Serial #N/A Good Condition

1 ea P410004 Ferguson 16/2-F475-270 Pipe Rotator with Clamping Roller System. 3,000 lb Load Capacity. 3" to 20" Diameter Capacity. Variable Speed Pipe Rotation by a Set of 12" Diameter Steel Wheel Turning Rolls with a Hold Down Devise. Turning Rolls are Mounted on a Constant Speed Side Arm Table that has 360 Degree Power Rotation. A Unique System for Welding Off Set Pipe and Pipe Elbows in Any Position. Serial #61418 Good Condition

P903008 Pandjiris model 30-6MVRMT 3,000 lb Positioner. 3,000 lb capacity @ 6" C.G., 135
degree constant speed power tilt, Variable speed rotation from .07 to 1.40 RPM. Manual adjustable height from 33" to 53" in 5" increments. 30" square table with slots. 25' pendant control. 230/460 volt. Serial #800-447247. Good Condition

P609002 Worthington Model 30P Positioner. 3,000 lb Capacity @ 6” C.G., Power tilt, Variable speed rotation from .031 to 1.24 rpm. 45” square table. Manual height adjustment from 42” to 72”in 6” increments. Pendant control. Serial #36268525. Good Condition

1 ea P708001 Worthington/Ransome Model 30P 3,000 lb Positioner. 3,000 lb capacity @ 6" C.G., Manual adjustable table height from 43" to 61" in 6" increments. Constant speed power tilt. Variable speed rotation from .030 to 1.20 RPM. 40" round table with slots. Pendant control for all functions. 230/460 volt. Serial #56109 Good Condition

1 ea P805013 Ransome Model 30P 3,000 lb Positioner. 3,000 lb capacity @ 6" c.g., Power tilt. Variable speed rotation from .03 to 1.2 RPM. Fixed table height of 38-3/4" to the center of the rotational axis. 40" square table with slots. Pendant control. 230 or 460 volt. Serial #4840 Good Condition

1 ea P611020 Aronson Model HS30GE/T4-62 Sky Hook Positioner. 4,000 lb Capacity @ 36" C.G. Off of the Turntable Face. 62" Clearance from Center of Turntable. "Skyhook" Positioners Provide Part Rotation in Two 360 Degree Axis which Result in Partial or Full Inverting of the Work piece. Pendant Control. Serial #7914 Good Condition

P810026 Aronson GE-45 Geared Elevation Positioner. 4,500 lb capacity @ 12” c.g.. 135 degree power tilt. .01 to 1.2 variable speed rotation. Powered elevation from 53” to 86”. 42” square table with slots. Pendant control. Serial # n/a Good Condition

P810018 Aronson X21E Geared Elevation Positioner. 5,000 lb capacity @ 6” c.g.. 135 degree power tilt. Variable speed power rotation. Powered elevation from 53” to 77”. 48” diameter round table with slots. Pendant control. Serial #665 Good Condition

1 ea RP309001P Koike-Aronson "1994" Model #RDCG/T6-100/26SD "Drop-Center" Positioner. Tilt Capacity of 6600 lbs @ 24" from the table, or 4000 lbs @ 57", or 2000 lbs @ 90"!!. Rotation Capacity of 6600 lbs @ 20" Center of Gravity off of the centerline of rotation. Both Tilt and Rotation Axis have Adjustable Anti-Backlash Dual Pinions on Bull Gears! Both Axis are Servo Drive Variable Speed with Encoders and Resolvers. 360 deg. Rotation @ 0.0-2.0 RPM, 200 deg. Tilt @ 0.0-1.75 RPM. (This Servo Drive Positioner can be converted to a Manual Pendant Operated Machine). Table is 48" x 48" with Hydraulic Master Clamping System for Slave Pallet Mounted Tooling 1 ea slave included. Note; "Drop Center Positioners" are typically used for work pieces with longer Center of Gravity distances from the table, resulting in lower working or welding heights than using higher capacity positioners. This 1994 Machine has NEVER BEEN USED! Brand New Condition!

P810001 Aronson 180T120/CC 180 Degree Tilter. 7,000 lb weight capacity @ 12” c.g. from table. Table tilts 180 degrees from vertical to vertical. For positioning long work pieces such as long truck frames for down hand welding. Table does NOT rotate. Table is a dual screw clamping table with an internal capacity of 40” wide x 27.5” high Very Good Condition

1 ea P805005 Teledyne-Readco Model UHSE-400 7,500 lb Side Arm Positioner. Side arm positioners are also known as Skyhook positioners. 7,500 lb capacity @ 6" c.g.. Dual screw driven powered elevation from 31.5" to 77.5" with the side arm table flat and parallel to the floor. 51" to the center of the rotational axis with the side arm at 90 degrees to the floor. Side arm table is 3.5" off set to the center of the rotational axis on the headstock. Variable speed rotation of the side arm table. 88" maximum part diameter capacity. Pendant control for all functions. 460 volt. Serial #106130 Good Condition

1 ea P805006 Teledyne-Readco Model UHSE-400 7,500 lb Side Arm Positioner. Side arm positioners are also known as Skyhook positioners. 7,500 lb capacity @ 6" c.g.. Dual screw driven powered elevation from 31.5" to 77.5" with the side arm table flat and parallel to the floor. 51" to the center of the rotational axis with the side arm at 90 degrees to the floor. Side arm table is 3.5" off set to the center of the rotational axis on the headstock. Variable speed rotation of the side arm table. 88" maximum part diameter capacity. Pendant control for all functions. 460 volt. Serial #106133 Good Condition

P808011 Aronson GE-90A 9,000 lb Geared Elevation Positioner. 9,000 lb capacity @12” c.g.., 135 degree power tilt. Variable speed rotation from .04 to 1.0 rpm. 33” powered geared elevation from 54.5” to 87.5”with the table flat. 42” diameter round table with a 9” diameter thru hole. Pendant control for all functions. Serial #7019. Good Condition

1 ea P001011 Aronson GE-1200-EXP, "1995" 120,000 lb Positioner. This Unique Positioner was Specially Designed by NASA to Assemble and "Float on Built-In Air Pads" a 2 Billion Dollar Spacecraft that was Launched in late December 1999. The Special Features are Numerous and
can be seen on our Space Website www.wpi-space-satellite.com or call Paul Rensing. Excellent Condition

P904007 Aronson C-1000 Universal Balance Positioner. 1,000 lb capacity @ 12” from the table. 360 degree manual rotation. Adjustable table height from 22” to 33”. 8” diameter work table. These are manual balanced machines – they are typically used for weldments that require quick re-positioning such as boxes, frames, etc.. Serial #n/a Good Condition

P904008 Aronson C-1000 Universal Balance Positioner. 1,000 lb capacity @ 12” from the table. 360 degree manual rotation. Adjustable table height from 22” to 33”. 8” diameter work table. These are manual balanced machines – they are typically used for weldments that require quick re-positioning such as boxes, frames, etc.. Serial #n/a Good Condition

P904005 Aronson C-2000 Universal Balance Positioner. 2,000 lb capacity @ 12” from the table. 360 degree manual rotation. Adjustable table height from 30” to 36”. 8” diameter work table. These are manual balanced machines – they are typically used for weldments that require quick re-positioning such as boxes, frames, etc.. Serial #n/a Good Condition

P904006 Aronson C-2000 Universal Balance Positioner. 2,000 lb capacity @ 12” from the table. 360 degree manual rotation. Adjustable table height from 30” to 36”. 8” diameter work table. These are manual balanced machines – they are typically used for weldments that require quick re-positioning such as boxes, frames, etc.. Serial #n/a Good Condition

1 ea P804001 Koike-Aronson C2000-P30 Universal Balance Positioner. 1500 lb Capacity @ 12" from the Table. Variable speed powered rotation from 0.1 to 6.0 rpm. Adjustable Height from 30" to 36". 8" Diameter Work Table. Serial #954228 Good Condition

P811004 Aronson C-2000 Universal Balance Positioner. 2,000 lb capacity @ 12” from the table. 360 degree manual rotation. Adjustable table height from 30” to 36”. 8” diameter work table. These are manual balanced machines – they are typically used for weldments that require quick re-positioning such as boxes, frames, etc.. Serial #811147 Good Condition

P810005 Aronson C-4000 Universal Balance Positioner. 4,000 lb capacity @ 12” from the table. 360 degree manual rotation. 48” fixed table height. 12: diameter work table. These are manual balanced machines – they are typically used for weldments that require quick re-positioning such as boxes, frames, etc.. Serial #83299 Good Condition

P810006 Aronson C-4000 Universal Balance Positioner. 4,000 lb capacity @ 12” from the table. 360 degree manual rotation. 48” fixed table height. 12: diameter work table. These are manual balanced machines – they are typically used for weldments that require quick re-positioning such as boxes, frames, etc.. Serial #75196 Good Condition

P810007 Aronson C-4000 Universal Balance Positioner. 4,000 lb capacity @ 12” from the table. 360 degree manual rotation. 48” fixed table height. 12: diameter work table. These are manual balanced machines – they are typically used for weldments that require quick re-positioning such as boxes, frames, etc.. Serial #n/a Good Condition

P810008 Aronson C-4000 Universal Balance Positioner. 4,000 lb capacity @ 12” from the table. 360 degree manual rotation. 48” fixed table height. 12: diameter work table. These are manual balanced machines – they are typically used for weldments that require quick re-positioning such as boxes, frames, etc.. Serial #n/a Good Condition

P810009 Aronson C-4000 Universal Balance Positioner. 4,000 lb capacity @ 12” from the table. 360 degree manual rotation. 48” fixed table height. 12: diameter work table. These are manual balanced machines – they are typically used for weldments that require quick re-positioning such as boxes, frames, etc.. Serial #n/a Good Condition

P810010 Aronson C-4000 Universal Balance Positioner. 4,000 lb capacity @ 12” from the table. 360 degree manual rotation. 48” fixed table height. 12: diameter work table. These are manual balanced machines – they are typically used for weldments that require quick re-positioning such as boxes, frames, etc.. Serial #n/a Good Condition

P810011 Aronson C-4000 Universal Balance Positioner. 4,000 lb capacity @ 12” from the table. 360 degree manual rotation. 48” fixed table height. 12: diameter work table. These are manual balanced machines – they are typically used for weldments that require quick re-positioning such as boxes, frames, etc.. Serial #n/a Good Condition

P810012 Aronson C-4000 Universal Balance Positioner. 4,000 lb capacity @ 12” from the table. 360 degree manual rotation. 48” fixed table height. 12: diameter work table. These are manual balanced machines – they are typically used for weldments that require quick re-positioning such as boxes, frames, etc.. Serial #n/a Good Condition

GUL WP-250 3/8 - 9" GRIPPER (inc. handle) (3/8-6.25", 4.25-10", 9.15-15") (3/8-6.25", 5.5-11.25'', 9.15-15'' - Clamping Range (min./max.)

IRC 3JC20 NEW Model 3JC20 Quickset Pipe Chuck. Clamping Diameter. Outside 5/8" to 15-1/2", Inside Clamp. 5" to 20", Quick-Set of 3-Jaws w/Pins. Mounting not Included NEW !

PAN TJ-20 NEW Model TJ-20 Quickset Gripper Chuck. Clamping Diameter. Outside 1" to 16-1/2", Inside Clamp. 6-1/4" to 20", Quick-Set of 3-Jaws w/Pins. Mounting not Included NEW !

PAN MOD-A NEW Model "A" Quickset Gripper Chuck. Clamping Diameter. Outside 1-1/2" to 27-5/8", Inside Clamp. 5-1/2" to 31-1/4". Quick-Set of 3-Jaws w/Pins. Mounting Not Included NEW !

IRC 3JC33 NEW Model 3JC33 Quickset Pipe Chuck. Clamping Diameter. Outside 5/8" to 28-1/2", Inside Clamp. 5" to 33". Quick-Set of 3-Jaws w/Pins. Mounting Not Included NEW !

PAN MOD-B NEW Model "B" Quickset Gripper Chuck. Clamping Diameter. Outside 1-1/2" to 40-3/4", Inside Clamp. 5-1/2" to 44-3/8". Quick-Set of 3 Jaws w/Pins. Mounting Not Included NEW !

PAN MOD-B-60 New Model "B-60" Quickset Gripper Chuck. Clamping Diameter. Outside 1-1/2" to 63-7/8". Inside 7" to 68". Quick-Set of 3 Jaws w/Pins. Mounting Not Included. NEW !!

CH904012 5” Diameter 3-Jaw Self Centering Scroll Chuck. 1/8” to 5” outside grip capacity. 1” to 6” inside grip capacity. 1-1/2” thru hole. Mounting NOT included. Good Condition

CH904014 8” Diameter 3-Jaw Self Centering Scroll Chuck. 1/4” to 8” outside grip capacity. 2” to 12” inside grip capacity. 4” thru hole. Mounting NOT included. Good Condition

CH904015 12” Diameter 3-Jaw Self Centering Scroll Chuck. 1/4” to 12” outside grip capacity. 4” to 14” inside grip capacity. 4” thru hole. Mounting NOT included. Good Condition

CH904016 12” Diameter 3-Jaw Self Centering Scroll Chuck. 3/8” to 12” outside grip capacity. 2-1/2” to 14” inside grip capacity. 4” thru hole. Mounting NOT included. Good Condition

CH904017 14” Diameter 3-Jaw Self Centering Scroll Chuck. 1/2” to 14” outside grip capacity. 2-1/2” to 20” inside grip capacity. 4-1/2” thru hole. Mounting NOT included. Good Condition

CH904013 26” Diameter 3-Jaw Self Centering Scroll Chuck. 1” to 26” outside grip capacity. 3-1/2” to 30” inside grip capacity. 9” thru hole. Mounting NOT included. Good Condition

CH802002 Aronson Model 3JC-40 3- Jaw Self Centering Welding Chuck. 3" minimum diameter capacity. 40" maximum diameter capacity. Good Condition

CH810029 Irco 3JC44 Gripper Style Chuck. 5/8” to 39.5” outside gripping capacity. 5” to 44” inside gripping capacity. Serial #n/a Good Condition

CH812005 Aronson Model 3JC5 3-Jaw Self Centering Scroll Chuck. 5” maximum outside clamping capacity. 7” maximum inside clamping capacity. 1-1/4” thru hole. Serial # n/a Good Condition

Any ARO HS2VF "NEW" Koike-Aronson 2,500 lb HeadStock. 2,500 lb load capacity @ 6" C.G., Variable speed rotation from .01 to 1.0 RPM. 27.75" Fixed height to the center of the rotational axis. 30" x 30" Square table with slots. 12’ Remote pendant control. 460 Volt. "NEW" In Stock

Any ARO TS2 "New" Koike-Aronson 2,500 lb Tailstock. 2,500 lb Load capacity @ 6" C.G., 27.75" Fixed height to the center of the rotational axis. 30" x 30" Square table with slots. "NEW" In Stock

Any ARO HS4VF "NEW" Koike-Aronson 4,500 lb HeadStock. 4,500 lb load capacity @ 6" C.G., Variable speed rotation from .01 to 1.0 RPM. 27.75" Fixed height to the center of the rotational axis. 30" x 30" Square table with slots. 12’ Remote pendant control. 460 Volt. "NEW" In Stock

Any ARO TS4 "New" Koike-Aronson 4,500 lb Tailstock. 4,500 lb Load capacity @ 6" C.G., 27.75" Fixed height to the center of the rotational axis. 30" x 30" Square table with slots. "NEW" In Stock

H810020 Aronson TS1000 1,000 lb Manual Special Utility Tailstock. 30” to 45” manual adjustable height to the center of the rotational axis. 360 degree manual rotation with brake and 45 degree pin lock. 8” diameter table. Serial #80683 Good Condition

H810021 Aronson TS1000 1,000 lb Manual Special Utility Tailstock. 30” to 45” manual adjustable height to the center of the rotational axis. 360 degree manual rotation with brake and 45 degree pin lock. 8” diameter table. Serial #76727 Good Condition

1 ea H606002 Bignall-Keeler Model 8A Dual Sided Headstock. 2,000 lb Weight Capacity. 10" Diameter Thru Hole Chuck Capacity. Variable Speed Rotation. 44" Fixed Height to the Center of the Rotational Axis. 230/460 Volt. Serial #5979 As-Is in Working Condition

1 ea H205007 Ransome 3T Tailstock Positioner. 3000 lb cap. @ 12" C.G. from Table Surface and 12" Eccentric from Rotation Center. 40" Square Table with Slots. Serial #63721 Good Condition

H904009 Pandjiris TS-50 Tailstock Only. 5,000 lb capacity @ 12” c.g., Manual rotation. 53” square table with mounting slots. 40” to the center of the rotational axis. Serial #n/a Good Condition

H903002 Aronson HTS-5AB Headstock/Tailstock. 5,000 lb capacity @ 6” c.g.. Constant speed rotation of 1.13 rpm (can be converted to variable speed). 30 square tables with mounting slots. Manual adjustable height from 27.75” to 49.75” in 6” increments. 230 or 460 volt. Serial #88631/88374. Good Condition

1 ea H805010 Aronson Model TS-6 6,000 lb Tailstock. 6,000 lb capacity @ 12" c.g.. Fixed table height of 36" to the center of the rotational axis. 48" square table with slots. Serial #n/a Good Condition

H810017 Aronson TS-6 6,000 lb Tailstock. Fixed height of 36” to the center of the rotational axis. 48” square table with slots. Serial #7162 Good Condition

H810016 Aronson TS-10AB 10,000 lb Tailstock. 36” to 66” manual adjustable height in 6” increments. 48” square table with slots. Serial #79167 Good Condition

1 ea H102204 Aronson HS-10 GE, 10,000 lb "Geared Elevation" Headstock Positioner. Capacity 5 Tons @12" C.G. from Table & Center of Rotation., Variable Speed Rotation by new AC Inverter Control. Powered Geared Elevation of 20" to 72" Cent. of Rot. from Floor. 36" dia. Round Table with 9" Thru Hole. Ser. #695. PM’d by Aronson. Very Good Condition

1 ea H805009 Aronson Model HS-10GE 10,000 lb Gear Elevation Headstock. 10,000 lb capacity @ 12" c.g., Powered geared elevation from 20" to 72" to the center of the rotational axis. Variable speed rotation from.04 to 1.0 rpm. Pendant control for all functions. 36" diameter round table. 230 or 460 volt. Serial #7725 Good Condition

1 ea H805002 Irco Model RHS-10 10,000 lb Headstock. 10,000 lb capacity @ 12" c.g., Variable speed rotation. Dual pinion drive. Fixed table height of 72" to the center of the rotational axis. 40" x 41.25" table. Pendant control for all functions. 230 or 460 volt. Serial #12398 Good Condition

1 ea H805017 Aronson Model RVTS12/20GE 12,000 lb Geared Elevation Tailstock on Variable Speed Travel Car with Track. 12,000 lb capacity @ 6" c.g.. Constant speed powered geared elevation from 57" to 178" to th center of the rotational axis. Mounted on a variable speed rack and pinion driven travel car with 46’ of track. Pendant control for all functions. 230 or 460 volt. Serial #n/a Good Condition

1 ea H1011005 Teledyne-Readco HTS-250, 12,500 lb Headstock Positioner. Capacity 12,500 lbs @ 12" (25,000 lbs @ 6" with Suitable Tailstock) Var. Speed Rotation by New AC Inverter Drive. 3 HP Motor. 54" x 54" Square Table with Tee Slots. Approx. 55" Ctr. of Rot. from Floor. Ser. # 105836 Good Condition

1 ea H805003 IGM System Model RF6000 13,200 lb Tailstock. 13,200 lb capacity @ 6" c.g., Fixed height of 87" to the center of the rotational axis. 59" diameter round table. 1988 date of mfg.. Serial #501699 Very Good Condition

1 ea H805004 IGM System Model RF6000 13,200 lb Tailstock. 13,200 lb capacity @ 6" c.g., Fixed height of 87" to the center of the rotational axis. 59" diameter round table. 1988 date of mfg.. Serial #501699 Very Good Condition

H810019 Aronson TS-16 16,000 lb Tailstock. Fixed height of 50” to the center of the rotational axis. 54: square table with slots. Serial # n/a Good Condition

1 ea H805011 Aronson Model RHS-16 16,000 lb Headstock. 16,000 lb capacity @ 12" c.g., Variable speed rotation from .02 to .60 rpm. Fixed height of 50" to the center of the rotational axis. 35" diameter mounting ring - no table. Pendant control for all functions. 230 or 460 volt. Serial #9115 Good Condition

1 ea H508004 Crossroads 90 Degree Indexing Headstock/Tailstock. 20,000 lb Concentric Load Capacity. To Index Part from Flat to 90 Degrees Only in one Direction and then Back to Starting Position. 59" to the Center of the Rotational Axis. Electric/Hydraulic Driven. 230/460 Volt Input. Good Condition

H809013 Aronson HTS-20 20,000 lb Headstock/Tailstock. 20,000 lb capacity @ 6” c.g., Variable speed rotation from .02 to 1.7 rpm. Dual pinion drive. 48” Square tables with an 8.5” diameter thru hole. 36” height to the center of the rotational axis. Pendant control. 230 or 460 volt. Serial # 9031/9019. Good Condition

H809014 Aronson HTS-20 20,000 lb Headstock/Tailstock. 20,000 lb capacity @ 6” c.g., Variable speed rotation from .02 to 1.7 rpm. Dual pinion drive. 48” Square tables with an 8.5” diameter thru hole. 36” height to the center of the rotational axis. Pendant control. 230 or 460 volt. Serial # 9034/9025. Good Condition

H809015 Aronson HTS-20 20,000 lb Headstock/Tailstock. 20,000 lb capacity @ 6” c.g., Variable speed rotation from .02 to 1.7 rpm. Dual pinion drive. 48” Square tables with an 8.5” diameter thru hole. 36” height to the center of the rotational axis. Pendant control. 230 or 460 volt. Serial # 9032/9024. Good Condition

H809016 Aronson HTS-20 20,000 lb Headstock/Tailstock. 20,000 lb capacity @ 6” c.g., Variable speed rotation from .02 to 1.7 rpm. Dual pinion drive. 48” Square tables with an 8.5” diameter thru hole. 36” height to the center of the rotational axis. Pendant control. 230 or 460 volt. Serial # 9031/9027. Good Condition

H809017 Aronson HTS-20 20,000 lb Headstock/Tailstock. 20,000 lb capacity @ 6” c.g., Variable speed rotation from .02 to 1.7 rpm. Dual pinion drive. 48” Square tables with an 8.5” diameter thru hole. 36” height to the center of the rotational axis. Pendant control. 230 or 460 volt. Serial # 9036/9020. Good Condition

1 set H211007 Teledyne Readco 20,000 lb Headstock/Tailstock. 20,000 lb Capacity @ 6" C.G., Variable Speed Rotation. 53" Diameter Round Table with Slots. Forward/off/Reverse Foot Pedal. Headstock is Mounted on a Screw Driven Variable Speed Travel Car on 9' of Track. Tailstock has a 24" Diameter Through Hole. Pendant Control for all Functions. Serial #106-633 Good Condition

2 sets H504001&2 Komatsu 25,000 LB Head/Tail Stocks. Cap. 25,000 @ 6" Center of Gravity off of the center line of Rotation. These Head/Tailstocks were used with a large Robotic Manipulator that was Welding Earth 20 ft. long Mover Boom Sections. They have Dual Directional Hydraulic Clamping Devices for holding the fixture or work pieces. They are designed for large Eccentric Loads and have integral counter weights. They now have Servo Motors that are 1500 rpm and 2.8 kw. and produce 2.1 rpm. The braking is done by a Hydraulic Disc Caliper. The Servo Motors can be replaced by an AC Inverter Drive for Manual Operation AS-IS No Changes We can Change to AC-Inverter Drive with Pendant Control Variable Speed

H809018 Aronson HTS-40 40,000 lb Headstock/Tailstock. 40,000 lb capacity @6: c.g., Variable speed rotation from .026 to .8 rpm. Dual pinion drive. 54” square tables with an 8” diameter thru hole. 50” height to the center of the rotational axis. Pendant control. 230 or 460 volt. Serial # 908. Good Condition

H809019 Aronson HTS-40 40,000 lb Headstock/Tailstock. 40,000 lb capacity @6: c.g., Variable speed rotation from .026 to .8 rpm. Dual pinion drive. 54” square tables with an 8” diameter thru hole. 50” height to the center of the rotational axis. Pendant control. 230 or 460 volt. Serial # 907.
Good Condition

H809020 Aronson HTS-40 40,000 lb Headstock/Tailstock. 40,000 lb capacity @6: c.g., Variable speed rotation from .026 to .8 rpm. Dual pinion drive. 54” square tables with an 8” diameter thru hole. 50” height to the center of the rotational axis. Pendant control. 230 or 460 volt. Serial # 906
Good Condition

H809025 Aronson HTS-40 40,000 lb Headstock/Tailstock. 40,000 lb capacity @6: c.g., Variable speed rotation from .026 to .8 rpm. Dual pinion drive. 54” square tables with an 8” diameter thru hole. 50” height to the center of the rotational axis. Pendant control. 230 or 460 volt. Serial # 909/905. Good Condition

H904003 Aronson HTS-40 40,000 lb Headstock/Tailstock. 40,000 lb capacity @6: c.g., Variable speed rotation from .026 to .8 rpm. Dual pinion drive. 36.5” round tables with a 19” diameter thru hole. 50” height to the center of the rotational axis. Pendant control. 230 or 460 volt. Serial # n/a
Good Condition

H904004 Aronson HTS-40 40,000 lb Headstock/Tailstock. 40,000 lb capacity @6: c.g., Variable speed rotation from .026 to .8 rpm. Dual pinion drive. 36.5” round tables with a 19” diameter thru hole. 50” height to the center of the rotational axis. Pendant control. 230 or 460 volt. Serial # n/a
Good Condition

Any ARO FT20VF NEW Koike-Aronson Model 20000-VF Floor Turntable. 20,000 lb capacity @ 12" C.G., Variable speed rotation from .025 to 1.0 RPM. 24" table height. 60" diameter table with slots. Pendant control. 460 volt. NEW

13 ea TT204001 Nashville Machine Co. Indexing Table. Capacity 1,000 lbs @ 6" Center of Gravity. Three Position Motorized Indexing Table with Air Clamping at Stop Position. 30" Diameter Round Table. 27" to 35" Adjustable Table Height by a Manual Screw Jack with Pin Locks in 1" Increments. Warning Buzzer for Rotational Movement. Foot Pedal. 115 Volt. Very Good Condition

1 ea FT102201 Reliance High Speed Turntable, with Magnetic Chuck. This is an Unique Variable Speed Turntable with a Speed Range up to 110 RPM. The 14" Table is a Magnetic Chuck with a Allen Key operated on/off switch. A Heavy Duty Unit. Very Good Condition

1 ea TI005005 Hercules 2000 lb Power Tilting Tables. Model TI-23842. 38" X 42" Table w/16" Lip, Electro-Hyd. Tilt of Approx. 75 Deg. 115v Input. Very Good Condition

1 ea TT306001 Advanced Lifts 2,000 lb Power Tilting Table. Model UE-290. 54" Long x 48" Wide two Sided Table. Electric/Hydraulic Tilt of 90 Degrees. 480 Volt. Serial #23497/1199 Very Good Condition

1 ea FT405002P VMW 100 Ton Floor Turntable. 200,000 lb Capacity @ 12" C.G., Variable Speed Drive with Forward and Reverse. 10' Diameter Round Table with a Fixed Height of 48". Pendant Control. (mw). Serial #N.A. Good Condition

Any Be-co Model F-400 Standard Universal Power Unit. Intended for both automatic and hand work, the F-400 is equipped with a ½-horsepower AC/DC motor, a 400:1 gear ratio, and dual-speed drive allowing either 3 to 20 or 5 to 30 inch-per-minute rotational speed. Our Standard BE-CO units will accommodate pipe sizes from 2" to 10’ diameters with quick-connecting expansion chains. "New"

Any Be-co NEW Model F-600 Heavy Duty Universal Power Unit. A heavy duty power unit with greater turning force for larger tank rotation This unit is identical to the Model F-400 standard power unit, but with a 600:1 gear ratio providing a choice of 2 to 13 1/3 or 3 1/3 to 20 ipm rotational speed."New

Any PRO TR1500 "New" Profax 1,500 lb Turning Rolls. 1,500 lb Turning Capacity (750 lb Max Set Down Weight for each the Drive and Idler). 1-1/2" to 16" Diameter Capacity. Variable Speed from 0.0 to 140 IPM. 10" Diameter x 2" Wide Rubber Wheels. High Frequency Protected. 115 Volt.

Any WPI TRD2000/WRI2000 "NEW" Weld Plus #2000 Turning Rolls. Drive Roll & Idler each have a capacity of 2000 lbs. For diameters from ½" to 40". 10" dia. wheels, High Frequency Protection, Variable Speed Control. With Foot Switch. 115 volt

Any GEN TR0100 "NEW" Gentec Model TR-0100 2,200 lb Turning Roll Set. 2,200 lb total weight capacity. 1" to 31" diameter capacity. Variable speed from 3.5 to 63 IPM. 2" wide x 8" diameter polyurethane wheels. High frequency protected. 115 volt

Any PAN PIPER 3 "NEW" Pandjiris Piper 3 Turning Rolls. 4,000 lb Load Capacity, Add an Additional Idler for a Total Capacity of 6,000 lb. 3-1/2" to 40" Diameter Capacity. Variable Speed from 2.0 to 60 IPM. Drive and Idler. 2-1/2" Wide X 12" Diameter Rubber Wheels. Drive and 1 ea. Idler. Pendant Control.

PRE RPJS 50 Preston-Eastin Model RPJS-50 5,000 lb Pipe Support Stand. 5,000 lb weight capacity. 2” to 40” diameter capacity. Manual adjustable height from 27.5” to 37.5” to the top of the rolls

Any WPI T6/I6 "NEW" Weld Plus #6000 Turning Rolls. 6000 lb Capacity Set Includes: 1 Drive Roll & 1 Idler Roll. Each Axle Has Double 10" X 2" Rubber Rolls. Speed Range 0 to 40 IPM, Pendant Speed Control, For Diameters From 3" to 72" via 3 Ctr. 115 volt. Ship Wt. 490 lbs/set.

Any WPI T9D 8 "NEW" Weld Plus #6000 Turning Rolls. 6000 lb Capacity (Add an additional idler for a total capacity of 9,000 lb.). Set Includes: 1 Drive Roll & 1 Idler Roll. Dual Driven Power Unit. Each Axle Has Double 10" X 2" Rubber Rolls. Speed Range 0 to 40 IPM, Pendant Speed Control, For Diameters From 3" to 96" via 4 Ctr. 115 volt. Ship Wt. 580 lbs/set.

WEB T-18/I-18 “NEW” 12,000 lb Turning Rolls. Set Includes 1 T-18 Driver and 1 I-18 Idler (add extra Idler for 18,000 lb Capacity). 12” Diameter Rubber Wheels, 2 Wheels per Axle for 7” Total Wheel Face – great for thin walled tanks !!. For Diameters from 12” to 12’. Variable Speed from 0 to 45 IPM. With Remote Pendant Control. 115 Volt. Ship Wt. 1,420 lbs/set

1 ea PAN TANKER 150/75 "NEW" Pandjiris 15,000 lb Tanker Turning Roll Set. 15,000 lb weight capacity. 3.5" to 12’ diameter capacity. Variable speed from 2.9 to 72 IPM. 25’ pendant control. 115 volt. No wheel adjustments to be made for the full range of diameters and Tankers maintain a constant center line !

WEB T-24/I-24 “NEW” 16,000 lb Turning Rolls. Set Includes 1 T-24 Driver and 1 I-24 Idler (add extra Idler for 24,000 lb Capacity). 12” Diameter Rubber Wheels, 3 Wheels per Axle for 10.5” Total Wheel Face F – great for thin walled tanks !!. For Diameters from 12” to 16’. Variable Speed from 0 to 45 IPM. With Remote Pendant Control. 115 Volt. Ship Wt.1,400 lbs/set.

WEB T-30/I-30 "NEW" Webb 20,000 lb Turning Rolls. Set Includes 1 T-30 Driver and 1 I-30 Idler (add extra Idler for 30,000 lb Capacity). 12" Diameter Rubber Wheels, 4 Wheels per Axle for 14" Total Wheel Face – great for thin walled tanks !!. For Diameters from 12" to 16'. Variable Speed from 0 to 45 IPM. With Remote Pendant Control. 115 Volt. Ship Wt. 1,750 lbs/set.

IRC 15 5D/5I “NEW” Irco Automation 20,000 lb Turning Rolls. Set includes 1 15-5 driver and 1 15-5 idler (add an additional idler for 30,000 lb total capacity). 12” diameter x 3” wide durable chemical resistant neoprene wheels, 2 wheels per axle for a 6” total wheel face. For diameters from 12” to 12’. Pull pin for easy adjustment of vessel size – no more losing bolts or looking for a wrench to make a size change !! Variable speed from 2 to 55 IPM. With remote pendant control. 460 Volt. Shipping Weight 1,550 lbs/set

1 set WEB R-500/I-500 "NEW" Webb 40,000 lb Turning Rolls. Set Includes 1 R-500 Drive and 1 I-500 Idler (add extra Idler for 60,000 lb Capacity). 18" Diameter Rubber Wheels, 1 Wheel per Axle with a Wheel Face of 7". For Diameters from 10" to 15’. Variable Speed from 7 to 58 IPM. With Remote Pendant Control. 230/460 Volt.

IRC 30 10D/10I “NEW” Irco Automation 40,000 lb Turning Rolls. Set includes 1 30-10 driver and 1 30-10 idler (add an additional idler for 60,000 lb total capacity). 12” diameter 4” wide durable chemical resistant neoprene wheels, 2 wheels per axle for an 8” total wheel face. For diameters from 12” to 12’. Pull pin for easy adjustment of vessel size – no more losing bolts or looking for a wrench to make a size change !! Variable speed from 2 to 55 IPM. With remote pendant control. 460 Volt. Shipping Weight 1,850 lbs/set.

ARO WRD-20/WRI-20 "NEW" Koike-Aronson 20 Ton Turning Rolls. Capacity: 1 Drive, 1 Idler 20 Tons. Add 1ea additional Idler (not included) Cap. 30 Tons. Three (3) 12" dia. X 4" Rubber Wheels per axle with Overload Disc. Variable Speed of 2 to 50 IPM surface speed.. For work diameters from 6" to 13 ft. Remote Pendant Control. Input Power 460 volt 1 phase

1 set WEB M-500/I-500 "NEW" Webb 40,000 lb Turning Rolls. Set Includes 1 M-500 Drive and 1 I-500 Idler (add extra Idler for 60,000 lb Capacity). 22" Diameter Rubber Wheels, 1 Wheel per Axle with a Wheel Face of 7". For Diameters from 24" to 14’. Variable Speed from 7 to 61 IPM. With Remote Pendant Control. 230/460 Volt.

1 set PAN MM30/15 "NEW" Pandjiris Missouri Mule 30/15 Turning Rolls. Drive and Idler. 60,000 lb Weight Capacity. 12" to 16’ Diameter Capacity. Variable Speed from 5.3 to 53 IPM. 20" Diameter x 10" Wide Rubber Wheels. Pendant Control. 460 Volt

IRC 45 15D/15I “NEW” Irco Automation 60,000 lb Turning Rolls. Set includes 1 45-15 driver and 1 45-15 idler (add an additional idler for 90,000 lb total capacity). 20” diameter x 4.5” wide durable chemical resistant polypropylene wheels. For diameters from 12” to 20’. Pull pin for easy adjustment of vessel size – no more losing bolts or looking for a wrench to make a size change !! Variable speed from 1.5 to 45 IPM. With remote pendant control. 460 Volt. Shipping Weight 3,550 lbs/set.

1 set WEB R-1000/I-1000 "NEW" 80,000 lb 40 ton Turning Rolls. Set Includes: 1 ea R-1000 Driver, 1 ea R-1000 Idler (add extra idler for 120,000 lb capacity). Rubber Wheel diameter 18" with 2 Wheels per axle for a Total Wheel face of 14". For Diameters from 10" to 20'. Variable Speed fro 7 to 58 IPM. With Remote Pendant Control. 1 year warranty. We stock 460 volt, 230 on request.

1 set T102214 "NEW" Webb R-1500, 120,000 lb 60 ton Turning Rolls. Set Includes: 1 ea R-1500 Driver, 1 ea R- 1500 Idler (add extra idler for 180,000 lb capacity). Rubber Wheel diameter 18" with 3 Wheels per axle for a Total Wheel face of 21". For Diameters from 10" to 22'. Variable Speed from 7 to 56 IPM. With Remote Pendant Control. 1 year warranty. We stock 460 volt, 230 on request.

ARO CPRR / CIRR “NEW” Ransome 60 Ton “C” Series Turning Roll Set. Set includes 1 each CPRR drive unit and 1 each CIRR idler unit for a capacity of 60,000 lb (add an additional idler for a total capacity of 90 ton.). Variable Speed drive from 1.45 to 58 ipm. 20.5” diameter x 14” wide rubber wheels. For diameters from 7” minimum to 20’ maximum. 20’ Pendant control for all functions. 460 volt. Shipping weight 5,600 lbs/set.

1 set RAN Koike Ransome "NEW" 100 Ton "MICARTA" Turbine Rotor Turning Rolls. Model 100 PRM Power Roll, Model 50IRM Idler Roll. Micarta Rolls are 22" diameter X 8" wide Micarta Surface. Roller Center Line Distance 23", For Shaft diameters from 8" to 32", 3 HP AC Inverter Drive, Variable Surface Speed of Roller from 1.5 to 60 IPM. Pendant Control w/40’ of Control Cable with Forward, Stop, Reverse, 10 Turn Pot. Speed Control and Rapid Traverse. Input Power Required 460 volts, 60 Hz. 3 phase.

1 set PRE Preston-Eastin "NEW" TDRA/TIRA-120, 240,000 lbs, 120 Ton, Turning Rolls. Set includes 1 ea TDRA-120, 120,000 lb Driver, and 1 ea TIRA 120,000 lb Idler. for a Total Capacity of 240,000 lbs or 120 tons. This set will Turn and Support 360,000 lbs or 180 tons by adding optional extra TIRA-120 Idler. Three (3) Tires 20" dia. x 8" wide and Four (4) Overload Disc per Axle. For work rotating diameters from 8" to 16 ft., Variable Speed Rotation by Inverter Drive with 20 ft Remote Pendant Control 460 volt input.

1 set PRE Preston-Eastin "NEW" TDRA/TIRA-120-22D, 240,000 lbs, 120 Ton, Turning Rolls. Set includes 1 ea TDRA-120, 120,000 lb Driver, and 1 ea TIRA 120,000 lb Idler. for a Total Capacity of 240,000 lbs or 120 tons. This set will Turn and Support 360,000 lbs or 180 tons by adding optional extra TIRA-120 Idler. Three (3) Tires 20" dia. x 8" wide and Four (4) Overload Disc per Axle. For work rotating diameters from 8" to 22 ft., Variable Speed Rotation by Inverter Drive with 20 ft Remote Pendant Control. 460 volt input.

1 set PAN PR180/60 "NEW" Pandjiris Model PR-180/60 Turning Rolls. Drive and Idler. 120,000 lb Weight Capacity (Add a Second Idler Roll for a Total Capacity of 180,000 lb). 12" to 21’ Diameter Capacity. Variable Speed from 3.0 to 75 IPM. 20" Diameter x 15" Wide Rubber Wheels. Pendant Control. 460 Volt

1 set PAN PR270/90 "NEW" Pandjiris Model PR-270/90 Turning Rolls. Drive and Idler. 180,000 lb Weight Capacity (Add a Second Idler Roll for a Total Capacity of 270,000 lb). 12" to 21’ Diameter Capacity. Variable Speed from 5.6 to 55.7 IPM. 20" Diameter x 20" Wide Rubber Wheels. Pendant Control. 460 Volt

1 ea T309002 Kistler / Pandjiris Model U-150 / U-150H Pipe Rotator with Clamping Roller System. 1" - 8" Clamping Range. 660 lb Horizontal Weight Capacity. 330 lb Vertical Weight Capacity. Variable Speed Rotation from 0 to 50 IPM. With Optional #151 Cart and Forward / Stop / Reverse/Variable Speed Rotary Foot Drum Control. An Excellent System for Flange and Elbow Welding on Small Diameter Pipe. 115 Volt. Good Condition

1 ea T603002 Ransome PTR Pipe Support Stand. 1,000 lb Weight Capacity. 2" to 36" Diameter Capacity. 8" Diameter x 2" Wide Steel Wheels. 8" Height Adjustment from 24" to 32". Serial #2918044 Good Condition

1 ea T612012 Pandjiris Model OS-15 Pipe Support Stand. 1,500 lb Capacity. 2" to 24" Diameter Capacity. Manual Adjustable Height. Serial #800-9138-1 Good Condition

1 ea T701005 Pandjiris Piper 3 Turning Rolls. 4,000 lb load capacity, 3-1/2" to 40" diameter capacity. Variable speed from 2.0 to 60 IPM. Drive and idler. 2-1/2" wide X 12" diameter steel wheels on both the drive and idler. Pendant Control. Serial #N/A Good Condition

1 ea T610008 Pandjiris Piper 3 Turning Rolls. 4,000 lb Load Capacity, 3-1/2" to 40" Diameter Capacity. Variable Speed from 2.0 to 60 IPM. Drive and Idler. 2-1/2" Wide X 12" Diameter Steel Wheels on the Powered Unit, Rubber on the Idler Unit. Pendant Control. Serial #N/A Good Condition

1 ea T505006 Pandjiris Piper 3 Turning Rolls. 4,000 lb Load Capacity, 3-1/2" to 40" Diameter Capacity. Variable Speed from 2.0 to 60 IPM. Drive and Idler. 2-1/2" Wide X 12" Diameter Rubber Wheels. Pendant Control. Serial #N/A Good Condition

1 ea T505007 Pandjiris Piper 3 Turning Rolls. 4,000 lb Load Capacity, 3-1/2" to 40" Diameter Capacity. Variable Speed from 2.0 to 60 IPM. Drive and Idler. 2-1/2" Wide X 12" Diameter Rubber Wheels. Pendant Control. Serial #N/A Good Condition

1 ea T505008 Pandjiris Piper 3 Turning Rolls. 4,000 lb Load Capacity, 3-1/2" to 40" Diameter Capacity. Variable Speed from 2.0 to 60 IPM. Drive and Idler. 2-1/2" Wide X 12" Diameter Rubber Wheels. Pendant Control. Serial #N/A Good Condition

T808003 Pandjiris Piper 3 2,000 lb Idler. 3.5” to 40” diameter capacity. 2,000 lb weight capacity. 12” diameter x 2.5” wide rubber wheels. Good Condition

T808004 Pandjiris Piper 3 2,000 lb Idler. 3.5” to 40” diameter capacity. 2,000 lb weight capacity. 12” diameter x 2.5” wide rubber wheels. Good Condition

T808005 Pandjiris Piper 3 2,000 lb Idler. 3.5” to 40” diameter capacity. 2,000 lb weight capacity. 12” diameter x 2.5” wide rubber wheels. Good Condition

T808006 Pandjiris Piper 3 2,000 lb Idler. 3.5” to 40” diameter capacity. 2,000 lb weight capacity. 12” diameter x 2.5” wide rubber wheels. Good Condition

T808007 Custom 2,000lb Idler Roll. 1.5” to 48” diameter capacity. 2,000 lb weight capacity. 10.5” diameter x 2.75” wide rubber wheels. Wheels manually adjust from 1.75 to 21” center to center by a threaded bolt. Good Condition

T808008 Custom 2,000lb Idler Roll. 1.5” to 48” diameter capacity. 2,000 lb weight capacity. 10.5” diameter x 2.75” wide rubber wheels. Wheels manually adjust from 1.75 to 21” center to center by a threaded bolt. Good Condition

T808009 Custom 2,000 lb Idler Roll. 1.5: to 60” diameter capacity. 2,000 lb weight capacity. 10.5” diameter x 2.75” wide rubber wheels. Wheel settings of 11” and 26” center to center. Good Condition

T8080010 Custom 2,000 lb Idler Roll. 1.5: to 60” diameter capacity. 2,000 lb weight capacity. 10.5” diameter x 2.75” wide rubber wheels. Wheel settings of 11” and 26” center to center. Good Condition

1 set T605003 Worthington "Ranger 3" Pipe Turning Rolls. 4,000 lb Capacity. 3.5" to 40" Diameter Capacity. Travel Speed from .9 to 37.7 IPM. 3" Wide x 12" Diameter Rubber Wheels. Drive & Idler. Pendant Control. 120 Volt. Serial #N/A Good Condition

1 ea T405001 Radian 3,000 lb Turning Rolls. Drive Roll with Idler. 3,000 lb Total Weight Capacity. 16" Diameter x 4" Wide Rubber Tires. Overload Discs. Constant Speed Friction Drive Rotation. 4" Minimum to 36" Maximum Diameter Capacity. 230/460 Volt. Electrical Re-Conditioned - No Clean Up or Paint Good Condition

1 ea T405002 Radian 3,000 lb Turning Rolls. Same As Above. Electrical Re-Conditioned - No Clean Up or Paint Good Condition

T904001 Ransome Ranger 3PR/3IR 4,000 lb Turning Rolls. 4,000 lb weight capacity. 3.5” to 40” diameter capacity. Variable speed from 1.2 to 37.7 IPM. 3.5” wide x 12” diameter rubber wheels. With pipe hold down devise. Currently mounted on 24” high stands. 115 volt. Serial #990272
Good Condition

1 ea T976004 Worthington Type A, 4000 lbs Driver Only. 15" dia. X 3" Wide Rubber Faced Rolls, Variable Speed, 12,000 lbs Turning Capacity. Good Condition

1 set T708014 Weldwire Model WWRD-2 4,000 lb Turning Rolls. 4,000 lb capacity for 1 drive and 1 idler. 3.5" to 40" diameter capacity. 12" diameter x 3" wide rubber wheels. Pendant control. 120 volt. Serial #9439/9471 Good Condition

1 ea T711010 Aronson WRI-5 5,000 lb Idler Roll. 5,000 lb weight capacity. 6" to 12’ diameter capacity. Idler Only !! Serial #n/a Good Condition

1 ea T711011 Aronson WRI-5 5,000 lb Idler Roll. 5,000 lb weight capacity. 6" to 12’ diameter capacity. Idler Only !! Serial #n/a Good Condition

T810023 Aronson WRI-5 5,000 lb Idler. 6” to 6’ diameter capacity. 12” diameter x 4.75” wide rubber wheels with overload discs. Serial #9304
Good Condition

T810028 Cayuga 5,000 lb Power Elevation Unit Frame Roll. 5,000 lb weight capacity. 24” minimum length capacity. 30” to 72” diameter capacity. Variable speed travel. Powered elevation from 36” to 48” to the top of the wheels. 12” diameter x 3” wide rubber wheels. 230 or 460 volt. Serial #28A86
Good Condition

1 ea T405003 Radian 5,000 lb Turning Rolls. Drive Roll with Idler. 5,000 lb Total Weight Capacity. 16" Diameter x 1" Wide Steel Wheels. Overload Discs. Constant Speed Chain Drive Rotation. 4" Minimum to 36" Maximum Diameter Capacity. 230/460 Volt. Electrical Re-Conditioned - No Clean Up or Paint Good Condition

1 ea T405004 Radian 5,000 lb Turning Rolls. Same as Above. Electrical Re-Conditioned - No Clean Up or Paint Good Condition $ 2,950. Converted to Variable Speed with Pendant

1 ea T409003 Ransome/Worthington AIRR Idler Roll. 5,000 lb Weight Capacity. 5" to 12’ Diameter Capacity. 2-1/2" Wide x 16" Diameter Rubber Wheels Good Condition

1 ea T409004 Ransome/Worthington AIRR Idler Roll. 5,000 lb Weight Capacity. 5" to 12’ Diameter Capacity. 2-1/2" Wide x 16" Diameter Rubber Wheels Good Condition

1 set T10805 Teledyne-Readco TRR-50, 5000 lb Steel Wheel Turning Rolls. Variable Speed ½ HP, 115 volt, Pendant Control of 2.5 to 75 IPM. 9" diameter x 4" wide Steel Wheels. For diameters from 3" to 66". Now set in unitized frame. 1980 Ser. #S-84563. Good Condition

2 ea T204001 Aronson T1I 6,000 Idler Roll. 6,000 lb Capacity. 24" Diameter x 3" wide Rubber Wheels. 4' Minimum Capacity, 10' Maximum Diameter Capacity. Idler Only. Serial #6049 Good Condition

1 ea T405007 Radian 10,000 lb Turning Rolls. Drive Roll and Idler. 10,000 lb Total Weight Capacity. 16" Diameter x 3.5" Wide Rubber Wheels. Constant Speed Rotation. 4" Minimum to 144" Maximum Capacity. 230/460 Volt. Electrical Re-Conditioned - No Clean Up or Paint Good Condition or Converted to Variable Speed with Pendant.

1 ea T209003 Aronson Model WPS4WD101-18 4-Wheel Drive Unit Frame Pipe Turning Roll. "1995" 10,000 lb Capacity. 18" Frame Length. 24" to 54" Diameter Capacity. 15" Diameter x 2.5" Wide Steel Wheels. Variable Speed from 2.0 to 50 IPM. Pendant Control. Used for Overlaying of Short Steel Mill Rolls. Serial #9580 Good Condition

T810025 Aronson WRD-10C Drive Roll. 10,000 lb weight capacity, 30,000 lb turning capacity. 12” to 6’ diameter capacity. Variable speed from 2 to 50 ipm. 20” diameter x 5” wide rubber wheels with overload discs. Serial #72033 Good Condition

1 ea T508003 Worthington "A" 10,000 lb Turning Rolls. 10,000 lb Weight Capacity.5" to 72" Diameter Capacity. Variable Speed Rotation from 6.1 to 61 IPM by a Sheave Drive. 16" Diameter x 3" Wide Rubber Wheels. On/Off Pendant. 230/460Volt. Drive and Idler. Serial #N/A "As-Is" Only or Completely Reconditioned

1 ea T508004 Worthington "A" 10,000 lb Turning Rolls. 10,000 lb Weight Capacity.5" to 12’ Diameter Capacity. Variable Speed Rotation from 6.1 to 61 IPM by a Sheave Drive. 16" Diameter x 3" Wide Rubber Wheels. On/Off Pendant. 230/460Volt. Drive and Idler. Serial #N/A "As-Is" Only or Completely Reconditioned

1 ea T704013 Aronson Model WRD-20 20,000 lb Drive Roll Only. 20,000 lb weight capacity. 60,000 lb turning capacity. 6" to 13’ Diameter capacity. 12" diameter x 13-3/8" rubber wheels. Variable speed from 2.0 to 50 IPM. Serial #83440 Good Condition

1 ea T209006 Aronson WRD-10/WRI-10 10 Ton Turning Rolls. 20,000 lb weight capacity. 6" to 13’ diameter capacity. Variable speed travel from 2 to 50 IPM. 12" diameter x 4" wide rubber wheels with over load discs. Drive & Idler. Serial #63132 Good Condition

1 ea T510016 Irco 10T-PR 10 Ton Turning Rolls. 20,000 lb Capacity, 12" to 60" Diameter Capacity. 19" Diameter x 4" Wide Rubber Wheels. Variable Speed Drive. Pendant Control. 230/460 Volt. Serial #5203 Good Condition

1 set TSP10802P Pandjiris MM-15T-SPL Rotation System for Ultrasonic Testing. This is a U.T. Rotation System for Digitally Indicated, Variable Speed, Turning of Cylindrical Parts under fluids flow. The System uses the Missouri Mule 15 Ton Turning Roll Configuration, Specially Manufactured for this type of Testing. The Drive Wheels are 16" dia. Grooved, Hardened Steel which are can be pivoted up and down for various workpiece diameters. The Idler Wheels are 6" Grooved, Hardened Steel , and have 13" of Motorized Powered Adjustable Height. There are "Vertical Thrust Rolls" on both driver and idler to prevent unwanted "walking". The Driver and Idler separation is adjustable for lengths from 24" to 100" by a long hand wheel screw. The whole system is in a fluid collection pan. Ser. #673-862 Very Good Condition

1 set TSP10801P Pandjiris MM-30T-SPL Rotation System for Ultrasonic Testing. This is a "1994" U.T. Rotation System for Digitally Indicated, Variable Speed, Turning of Cylindrical Parts under fluids flow. The System uses the Missouri Mule 30 Ton Turning Roll Configuration, Specially Manufactured for this type of Testing. The Drive Wheels are 20" dia. Grooved, Hardened Steel which are can be pivoted up and down for various workpiece diameters. The Idler Wheels are 6" Grooved, Hardened Steel , and have 14" of Motorized Powered Adjustable Height. There are "Vertical Thrust Rolls" on both driver and idler to prevent unwanted "walking". The Driver and Idler separation is adjustable for lengths from 30" to 120" by a long hand wheel screw. The whole system is in a fluid collection pan fitted with removable platform slat sections. Ser. #SO. 60-4604 This is a "Ready to Ship" Rotation System in Excellent Condition

1 ea T704008 Aronson Model WRD-30 30,000 lb Drive Roll Only. 30,000 lb weight capacity. 90,000 lb turning capacity. 8" to 18’ diameter capacity. Variable speed from 1.4 to 40 IPM. 20" diameter x 7" wide rubber wheels with overload discs. 240/460 volt. Serial #N/A Good Condition

T808002 Ransom SA-15PR/SA-7.5IR “Rustler” 15 Ton Turning Roll Set. Drive and Idler. Ransome Rustler rolls automatically adjust to take any circular piece from 12” to 10’ diameter. 30,000 lb weight capacity. 12” diameter x 3.5” wide rubber wheels. Variable speed travel from 4.8 to 48 ipm. Pendant Control. 230 or 460 volt. Serial #7925369/8025370 Good Condition

T810024 Ransome BIRR 45,000 lb Idler. 15 tons 7” to 8’ diameter capacity. 20.5” diameter x 7” wide rubber wheels. Serial #364298 Good Condition

T901015 Ransome Model BIRR 15 Ton Idler Roll Only. 30,000 lb weight capacity. 7” to 20’ diameter capacity. 7” x 20” diameter rubber wheels. Serial #6726407 Good Condition

T901016 Ransome Model BIRR 15 Ton Idler Roll Only. 30,000 lb weight capacity. 7” to 14’ diameter capacity. 7” x 20” diameter rubber wheels. Serial #n/a Good Condition

T901017 Ransome Model BIRR 20 Ton Idler Roll Only. 40,000 lb weight capacity. 7” to 20’ diameter capacity. 7” x 20” diameter rubber wheels. Serial #3626324 Good Condition

T901011 Aronson Model WRI-60 30 Ton Idler Only. 60,000 lb weight capacity. 8” to 18’ diameter capacity. 12” wide x 20” diameter rubber wheels. Serial #n/a Good Condition

T901012 Aronson Model WRI-60 30 Ton Idler Only. 60,000 lb weight capacity. 8” to 18’ diameter capacity. 12” wide x 20” diameter rubber wheels. Serial #n/a Good Condition

T901021 Pandjiris Unit Frame 34 Ton Turning Rolls on Variable Speed Travel Car. 68,000 lb turning capacity. 7’ to 14’ diameter capacity with a fixed axel center of 72”. Variable speed rotation. 5 sets of 5” wide x 20” diameter rubber wheels spaced over the 30’ length of a variable speed travel car that runs on 69” gauge rail track. Pendant control. Serial # 60-4595 Good Condition

T901022 Pandjiris Unit Frame 34 Ton Turning Rolls on Variable Speed Travel Car. 68,000 lb turning capacity. 7’ to 14’ diameter capacity with a fixed axel center of 72”. Variable speed rotation. 5 sets of 5” wide x 20” diameter rubber wheels spaced 30’ over the length of a variable s. Good Condition

T901013 Ransome Model BPRR/BIRR 30 Ton Turning Roll Set. 60,000 lb weight capacity (add an additional idler for a total capacity of 90,000 lb). 7” to 12’ diameter capacity. 7” wide x 20” diameter rubber wheels. Variable speed rotation from 1.45 to 58 ipm. Pendant control. 230 or 460 volt. Serial #3533295/3633841 Good Condition

T901014 Ransome Model BPRR/BIRR 30 Ton Turning Roll Set. 60,000 lb weight capacity (add an additional idler for a total capacity of 90,000 lb). 7” to 20’ diameter capacity. 7” wide x 20” diameter rubber wheels. Variable speed rotation from 1.45 to 58 ipm. Pendant control. 230 or 460 volt. Serial #665832/3626430 Good Condition

T901018 Ransome Model CPRR 30 Ton Drive Roll Only. 60,000 lb weight capacity, 180,000 lb turning capacity. 7” to 20’ diameter capacity. 14” wide x 20” diameter rubber wheels. Variable speed rotation from 1.45 to 58 ipm. Pendant control. 230 or 460 volt. Serial #3725801
Good Condition

T901019 Ransome Model CPRR 30 Ton Drive Roll Only. 60,000 lb weight capacity, 180,000 lb turning capacity. 7” to 20’ diameter capacity. 14” wide x 20” diameter rubber wheels. Variable speed rotation from 1.45 to 58 ipm. Pendant control. 230 or 460 volt. Serial #1305 Good Condition

T901020 Ransome Model CPRR 30 Ton Drive Roll Only. 60,000 lb weight capacity, 180,000 lb turning capacity. 7” to 20’ diameter capacity. 14” wide x 20” diameter rubber wheels. Variable speed rotation from 1.45 to 58 ipm. Pendant control. 230 or 460 volt. Serial #n/a Good Condition

T901030 Ransome Model CIRR 30 Ton Idler Roll Only. 60,000 lb weight capacity. 7” to 14’ diameter capacity. 14” wide x 20” diameter rubber wheels. Serial #n/a Good Condition

T901010 Aronson Model WRD-60/WRI-60 60 Ton Turning Roll Set. 120,000 lb weight capacity (add an additional idler for a total capacity of 180,000 lb). 8” to 18’ diameter capacity. Variable speed from 1.4 to 40 ipm. 12” wide x 20” diameter rubber wheels with overload discs. Pendant control. 230 or 460 volt. Serial #n/a Good Condition

T810030 Aronson WND60CS-86 Turbine Turning Roll Set. 60 ton capacity. 8” to 6’ diameter capacity. Constant speed rotation. 27” diameter x 5.75” wide neoprene wheels. Serial #7386 Good Condition

T901003 Ransome Model DPRRPT/DIRRPT 90 Ton Turning Roll Set. 180,000 lb capacity. 4’ to 10’ diameter capacity. 16” wide x 42” diameter foam filled rubber truck tires. Pendant Control. 460 volt. Serial #3931611/4031261 Good Condition

T901004 Ransome Model DPRRPT/DIRRPT 90 Ton Turning Roll Set. 180,000 lb capacity. 4’ to 10’ diameter capacity. 16” wide x 42” diameter foam filled rubber truck tires. Pendant Control. 460 volt. Serial #3931612/4031615 Good Condition

T901005 Ransome Model DPRRPT/DIRRPT 90 Ton Turning Roll Set. 180,000 lb capacity. 4’ to 10’ diameter capacity. 16” wide x 42” diameter foam filled rubber truck tires. Pendant Control. 460 volt. Serial #3931253/4032376 Good Condition

T901006 Ransome Model DPRRPT/DIRRPT 90 Ton Turning Roll Set. 180,000 lb capacity. 4’ to 10’ diameter capacity. 16” wide x 42” diameter foam filled rubber truck tires. Pendant Control. 460 volt. Serial #na/4033765 Good Condition

T901007 Ransome Model DPRRPT/DIRRPT 90 Ton Turning Roll Set. 180,000 lb capacity. 4’ to 10’ diameter capacity. 16” wide x 42” diameter foam filled rubber truck tires. Pendant Control. 460 volt. Serial #na/na Good Condition

T901008 Ransome Model DPRRPT/DIRRPT 90 Ton Turning Roll Set. 180,000 lb capacity. 4’ to 10’ diameter capacity. 16” wide x 42” diameter foam filled rubber truck tires. Pendant Control. 460 volt. Serial #3933763/4033766 Good Condition

1 ea T605019 Teledyne-Readco 150 Ton Turbine Rolls. 150 Ton Weight Capacity. 4" to 48" Diameter Capacity. Variable Speed Electric/Hydraulic Drive. 23-1/2" Diameter x 16" Wide Rubber Wheels. Drive and Idler. Serial #105839/105840 Very Good Condition

1 set T008002P Aronson 200 Ton "Twin Driver" Turning Rolls. Model WSD-200-S2G. 3’ to 10’ diameter capacity. Twin Driver Turning Rolls use one Driven Wheel on each Roll Stand. Also one of these driven wheels has Two Final Gear Drive Worm Gears on each side of the axle, thus the two pinions work in opposite directions to Eliminate Backlash. This Design was developed by Aronson for Babcock & Wilcox so the turning rolls could be used under Vertical Boring Mills. Ser.# 667 Good Condition

1 ea ARO 99 10X10 "NEW" Ransome Model 99 10’ x 10’ Manipulator. 10’ Constant Speed Power Lift at 40 IPM from 28-1/2" to 148-1/2" to the center of the Boom. 10’ Variable Speed Power Reach of 1.5 to 150 IPM from 24" to 144" from the Center of the Mast. 500 lb Weight Capacity Either or Both Ends. 360 Degree Manual Rotation on a Bolt Down Base. Joy Stick Control

1 ea ARO 99BS "NEW" Ransome Free Standing Base. For Model 99 10’ x 10’ Manipulator

3 ea ARO 99 12X10 "NEW" Ransome Model 99 12’ x 10’ Manipulator. 12’ Constant Speed Power Lift at 40 IPM from 28-1/2" to 172-1/2" to the center of the Boom. 10’ Variable Speed Power Reach of 1.5 to 150 IPM from 24" to 144" from the Center of the Mast. 500 lb Weight Capacity Either or Both Ends. 360 Degree Manual Rotation on a Bolt Down Base. Joy Stick Control

3 ea ARO 99 12X12 "NEW" Ransome Model 99 12’ x 12’ Manipulator. 12’ Constant Speed Power Lift at 40 IPM from 28-1/2" to 172-1/2" to the center of the Boom. 12’ Variable Speed Power Reach of 1.5 to 150 IPM from 24" to 168" from the Center of the Mast. 500 lb Weight Capacity Either or Both Ends. 360 Degree Manual Rotation on a Bolt Down Base. Joy Stick Control.

1 ea ARO 99BL "NEW" Ransome Optional Free Standing Base. For Model 99 12’ x 10’ or 12’ x 12’ Manipulator

1 ea ARO 1212 14X12 "NEW" Ransome Model 1212 14’ x 12’ Manipulator. 14’ Constant Speed Power Lift at 36 IPM from 28-1/2" to 148-1/2" to the center of the Boom. 12’ Variable Speed Power Reach of 1.8 to 180 IPM from 30-1/2" to 174-1/2" from the Center of the Mast. 750 lb Weight Capacity Either or Both Ends. 360 Degree Manual Rotation on a Bolt Down Base. Joy Stick Control

1 ea ARO 1212 14X14 "NEW" Ransome Model 1212 14’ x 14’ Manipulator. 14’ Constant Speed Power Lift at 36 IPM from 28-1/2" to 148-1/2" to the center of the Boom. 14’ Variable Speed Power Reach of 1.8 to 180 IPM from 30-1/2" to 198-1/2" from the Center of the Mast. 750 lb Weight Capacity Either or Both Ends. 360 Degree Manual Rotation on a Bolt Down Base. Joy Stick Control.

1 ea ARO 1212BL "NEW" Ransome Optional Free Standing Base. For Model 1212 14’ x 12’ or 14’ x 14’ Manipulator

1 ea WPI TCM "NEW" Universal Manipulator Variable Speed Travel Car. Variable Speed Travel from 3" to 135" IPM that runs on 56-1/2" A.S.C.E. 60# Machined Rail Track. Pendant Control. 230/460 Volt. "NEW"

Any WPI TCT "New" Universal Track for Manipulator Travel Car. 10’ x 56-1/2" A.S.C.E. 60# Machined Rail Track

8 ea M610004 Positech Model "G" Simple Air Manipulator. Positech Model G SAM Parts Manipulator uses Pneumatic Power to Provide Quick Response and Superior Maneuverability with Loads up to 370 lbs. Vertical Lift from 44.7" to 87.3". Reach from 66" to 126". 360 Degree Full Rotation. Includes Portable Base with Fork Truck Lifting Slots. Good Condition

M903005 Pandjiris Model 172H Head Director Manipulator. Motorized torch height from 40” to 112”. Manual torch reach from 43-3/8” to 91-1/4”. 360 degree manual mast rotation. Mounted on a portable floor mount base. 230 or 460 volt. Serial #800-3542-8 Good Condition

1 ea M806001 Roller & Assoc. Head Director Manipulator on Manual Travel Car. Adjustable height from 49" to 112" by a manual hand pump hydraulic cylinder. Reach 71" when at 49", 43" reach when at 112" and 74" reach with the arm level. 360 degree manual mast rotation. 4" manual cross slides mounted on the end of the boom arm. All mounted on a manual travel car. Serial #n/a Good Condition

1 ea M409001 Porta Tools / Lincoln Model H-600 26" x 48" Manipulator. Constant Speed Power Reach from 24" to 50", Screw Driven Constant Power Elevation from 12" to 60". Lincoln DC-600 Power Supply and a NA-5 Submerged Arc Control and Head, Lincoln Manual Horizontal and Vertical Adjusters. All Mounted on a Variable Speed Travel Car with 40’ of Track. Serial #W7702-0270 Good Condition

1 ea M606017 Ransome Model 44 4’ x 4’ Manipulator / Travel Car. 4’ Constant Speed Powered Lift from 25" to 73". Manual Reach from 9" to 57" from the Center of Mast Rotation. Manual King Pin Base. Manual Travel Car. 115 Volt. Serial #0526806 Good Condition

M901023P Pandjiris 4’ x 37’ Telescoping Boom Manipulator. 191” overall height. 48” constant speed powered elevation from 57-3/4” to 105-3/4” to the centerline of the arm. 3 to 116 IPM variable speed powered reach telescoping boom with a total reach of 37’6”. Fixed non swivel bolt down base. 460 volt. Serial #60-4596 Good Condition

M810004 Aronson S6VRA6CL-MK 6’ x 6’ Scarab I Manipulator. 1,700 lb load capacity either or both ends. 6’ constant speed power lift from 40.5” to 112.5”. 3.3 to 100 IPM variable speed reach from 18” to 90”. 360 degree manual mast rotation. Floor mount base. 460 volt. Serial #7448
Good Condition

M903004 Preston-Eastin MA-66MD 6’ x 6’ Manipulator. 150 lb weight capacity either or both ends. 6’ powered lift from 24-1/4” to 96-1/4”. 6’ 4.0 to 100 IPM variable speed powered reach from 18-1/2” to 90-1/2”. 360 degree manual mast rotation. Bolt down base. 115 volt. Serial #MB66MD-27 Good Condition

M810002 Aronson G8CR6ML-PK 6’ x 8’ Locust I Manipulator. 300 lb load capacity either or both ends. 6’ Constant speed power lift from 29” to 101”. 8’ manual reach from 14” to 120”. 360 degree manual mast rotation. Mounted on a portable king pin base. 110 volt. Serial #72104
Good Condition

M810003 Aronson G6CR6ML-PK 6’ x 8’ Locust I Manipulator. 300 lb load capacity either or both ends. 6’ Constant speed power lift from 29” to 101”. 3.3 TO 100 IPM variable speed reach from 14” to 86”. 360 degree manual mast rotation. Mounted on a portable king pin base. 110 volt. Serial #75236
Good Condition

M904018 Ransome Model XXHD 7’ x 15’ Travel Car Manipulator. 7’ powered elevation from 77” to 164” to the bottom of the boom. 2.7 to 108 IPM variable speed reach from 64” to 244” from the center of the mast rotation. 360 degree power mast rotation. 2,000 lb load capacity either or both ends. Mounted on a variable speed travel car that runs on 84” gauge rail track. Track NOT Included. 460 volt. Serial #909286 Reconditioned Price or As-Is Price

1 ea M309004 Mark "V" 8' x 5' Manipulator and Travel Car. 8' Constant Speed Power Elevation from 32" to 128". 5' Variable Speed Power Reach from 15" to 75". Manual Mast Rotation. With 6" Linde Powered Horizontal and Vertical Cross Slides and a Manual Rotary Slide. All Mounted on a Manual Travel Car that Runs on Inverted Angle Iron Track (Track Not Included). Currently Equipped with a L-Tec 650 CC/CV Power Supply, GMA Feed Head and all Cables. Remote Control Console for all functions Including Welding Process. Serial #6620-34-31 Good Condition

M903006 Pandjiris Model 1000 9’ x 9’ Manipulator. 400 lb capacity either or both ends. 9’ power elevation from 16” to 124”. 9’ 18-1/4” to 127-1/4” variable speed reach from 3 to 116 IPM. 360 degree manual mast rotation. Bolt down base. 460 volt. Serial #800-4308-5 Good Condition

1 ea M712001 Pandjiris Double 8 10’ x 8’ Manipulator. 10’ constant speed power elevation from 22" to 139". 3" to 110" variable speed reach from 21" to 117" (8’). 360 degree manual mast rotation. 300 lb weight capacity either end, 500 lb combined weight capacity. Bolt down floor mount base. 460 volt. Serial #81-2159-1 Good Condition

1 ea. M404001 Precision 9’ x 9’ x 27-1/2’ Heavy Duty Manipulator/Travel Car System. This system was manufactured for the Robotics Industry for precision welding on military vehicles. Heavy Duty Mast has 9 ft. of constant speed of precision screw driven lift starting at approx. 36" from the floor to 144" high under the boom. The mast has manual rotation with lock. Boom has 9 ft. of "Dual Pinion" variable speed gear drive and rolls on Thompson Roundway roller system. Weight capacity approx. 750 lb. Travel car is 5’ x 5’ x 19" High and Variable Speed Rack & Pinion Drive on 33 ft. of Thompson Roundway Precision Track. All three (3)-axis paths are accordion booted. This system is now Servo driven. We will change to Pendant AC-Inverter or D.C. Drives. Very Good Condition

1 ea M709002P Ransome Model 66 10’ x 10’ Manipulator. 10’ Constant speed powered cable lift from 18" to 138" to the floor. 10’ Variable speed powered reach from 15" to 135" from the center of the mast rotation. 360 Degree manual rotation. Shop built fall safe device. NOT for sub-arc applications! 115 volt. Serial #649830 Currently in Working Condition - As-Is Only

M803009 Aronson Model S10VRA14CL Scarab I Manipulator. 1,300 lb load capacity either or both ends. 14’ constant speed power lift from 38.75” to 206.75”. 3.3 to 100 IPM variable speed reach from 43” to 163”. King pin base for 360 degree manual mast rotation. 460 volt. Serial #81280
Good Condition

M807004 Ransome Model 1212 12’ x 12’ Travel Car Manipulator. 750 lb weight capacity either or both ends. 38 ipm constant speed power lift from 62.25” to 206.25”. 3.35 to 134 ipm variable speed reach from 39.5” to 183.5”. 360 degree manual mast rotation. Mounted on a 33 gauge rack and pinion travel car with a speed range from 5 to 200 ipm. Travel car includes 30’ of track. Pendant control for all functions. Welding equipment NOT included. 460 volt. Serial #692597 Good Condition

M710002 Ransome Model XXHD 13.5’ x 18’ Travel Car Manipulator. 13.5’ powered elevation from 77-1/2” to 239-1/2”” to the bottom of the boom. 2.7 to 108 IPM variable speed reach from 55” to 271” from the center of the mast rotation. 360 degree power mast rotation. 2,000 lb load capacity either or both ends. Mounted on a variable speed travel car that runs on 84” gauge rail track. Track NOT Included. 460 volt. Serial #639089 Reconditioned Price or As-Is Price

M803009 Aronson Model S10VRA14CL 14’ x 10’ Manipulator. 1,300 lb load capacity either or both ends. 14’ constant speed powered lift from 36.5 " to 204.5". 10’ of 3.3 to 100 IPM variable speed reach from 43" to 163". 360 degree manual mast rotation. Bolt down base. 460 volt. Serial #81280 Good Condition

1 ea M901002 Pandjiris 1400 Series 14 x 15 Manipulator. 750 lb weight capacity either or both ends. 14’ powered elevation from 26-3/8” to 194-3/8”. 15’ variable speed powered reach from 32” to 212” from the center of the mast rotation. Fixed bolt down base. (We can quote with this machine equipped with a manual mast rotation). 230 or 460 volt. Serial #600-3867-2 Good Condition

1 ea M901009 Pandjiris 1400 Series 14 x 15 Manipulator. 750 lb weight capacity either or both ends. 14’ powered elevation from 26-3/8” to 194-3/8”. 15’ variable speed powered reach from 32” to 212” from the center of the mast rotation. Fixed bolt down base. (We can quote with this machine equipped with a manual mast rotation). 230 or 460 volt. Serial #600-3866-4 Good Condition

1 ea JET LWS36 "NEW" Jetline Model LWS-36 36" Longitudinal GTAW seam Welding Package. 42" Total Clamping/Welding Length. Minimum Part Diameter Capacity of 3.25". Maximum Part Diameter Capacity of 32" (Can be Increased with a Riser). Gas Purge Back-up Bar. Plate Edge Alignment Devices. Variable Speed Carriage. Jetline Model 9627 Weld Sequence Control, ALC-401-6 Arc Length Control, CWF-10B Cold Wire Feeder and a Miller Maxstar 350 Tig Welding Package that Includes a Water Circulator and 500 amp Tig Torch. Brand New

GEN LS12 "NEW" Gentec Model LS-12 4’ Longitudinal Seam Welder. 51" Total Welding/Clamping Length Capacity. .040 to 3/8" Thickness Capacity. 4" Minimum Part Diameter. 30" Maximum Part Diameter. Variable Speed Rack & Piniod Driven Carriage from 1.2 to 29 IPM. Pneumatic Torch Lifter. Automatic Gas Purge System. Automatic Pneumatic Mandrel Clamping Devise. Pneumatic Plate Alignment Devise. Automatic Finger Release. Copper Gas Purge Back-up Bar. Welding Equipment NOT Included. NEW IN STOCK !! Ready to Mount Your Welding Process

1 ea JET LWS48 "NEW" Jetline Model LWS-48 48" Longitudinal GTAW seam Welding Package. 54" Total Clamping/Welding Length. Minimum Part Diameter Capacity of 3.25". Maximum Part Diameter Capacity of 32" (Can be Increased with a Riser). Gas Purge Back-up Bar. Plate Edge Alignment Devices. Variable Speed Carriage. Jetline Model 9627 Weld Sequence Control, ALC-401-6 Arc Length Control, CWF-10B Cold Wire Feeder and a Miller Maxstar 350 Tig Welding Package that Includes a Water Circulator and 500 amp Tig Torch. Brand New

1 ea JET LWS60 "NEW" Jetline Model LWS-60 60" Longitudinal GTAW seam Welding Package. 66" Total Clamping/Welding Length. Minimum Part Diameter Capacity of 5.25". Maximum Part Diameter Capacity of 32" (Can be Increased with a Riser). Gas Purge Back-up Bar. Plate Edge Alignment Devices. Variable Speed Carriage. Jetline Model 9627 Weld Sequence Control, ALC-401-6 Arc Length Control, CWF-10B Cold Wire Feeder and a Miller Maxstar 350 Tig Welding Package that Includes a Water Circulator and 500 amp Tig Torch. Brand New

1 ea JET LWS72 "NEW" Jetline Model LWS-72 72" Longitudinal GTAW seam Welding Package. 78" Total Clamping/Welding Length. Minimum Part Diameter Capacity of 6.0". Maximum Part Diameter Capacity of 32" (Can be Increased with a Riser). Gas Purge Back-up Bar. Plate Edge Alignment Devices. Variable Speed Carriage. Jetline Model 9027 Weld Sequence Control, ALC-401-6 Arc Length Control, CWF-10B Cold Wire Feeder and a Miller Maxstar 350 Tig Welding Package with a Water Circulator and 500 amp Tig Torch. Brand New

1 ea JET LWS72G "New" Jetline Model LWS-72 72" Longitudinal Seam Welding Package. 78" Total Clamping/Welding Length. Minimum Part Diameter of 6.0". Maximum Part Diameter Capacity of 32" (Can be Increased with a Riser). Gas Purge Back-up Bar. Plate Edge Alignment Devices. Variable Speed Carriage. Jetline Model 9627 Weld Sequence Control. Ready to Mount Your Welding Process !! Brand New

1 ea S209001 Jetline 6" Custom Weld Seamer. 1997 Variable Speed Jetline Carriage on a Jetline Model TKS-24 Side Beam with 24" Travel. Currently Has a Total Clamping Length of 6" (Can be Increased with a New Clamping Fixture to a Length of 24" to Match Side Beam). 3" Vertical and Horizontal Cross Slides and a Rotary Slide. No Welding Equipment!! Serial #970295 Good Condition

1 ea S209003 Jetline 6" Custom Weld Seamer. 1997 Variable Speed Jetline Carriage on a Jetline Model TKS-24 Side Beam with 24" Travel. Currently Has a Total Clamping Length of 6" (Can be Increased with a New Clamping Fixture to a Length of 24" to Match Side Beam). 3" Vertical and Horizontal Cross Slides and a Rotary Slide. Complete with Plasmfix 50S Plasma Welding Power Supply and Miller Water Circulator. Serial #970299 Good Condition

1 ea S604011 "1990"Mills Machine 11" Longitudinal Plasma Seam Welder. 11" Overall Welding / Clamping Length Capacity. 3-1/2" to 5-1/2" Diameter Capacity ( Can be Increased with a Riser ). Variable Speed Screw Driven Carriage. 3" Pneumatic Torch Lifter. Gas Purge Back p Bar, Water Cooled Mandrel, Dual Water Circulators. Plasma Welding Equipment Includes a Thermal Dynamics WC100B Welding Console, Airco Heliwelder Power Supply and Multi Slope 2 Sequence Control, Model 3A Plasma Torch and a Cyclomatic 80A Magnetic Welds Oscillator. Serial # N/A Good Condition

1 ea S502007 Jetline 12" Coil End Joining Seam Welder. This seam welder’s primary use is to join together strips fed from coils. The Jetline Seamer Clanping/Welding bed is 12-1/2" long. Has a Variable Speed Carraige with #9026 Control and two manual cross slides on the torch holder. The one piece hold down clamps are air actuated with individual air valves. There are 2 ea 8" dia. primary strip guide rolls and 2 ea 3" final guide rolls. The Welding Package is a Miller 50A Precision Tig Welding Power Supply and and Air-Cooled Tig Torch for the fusion only weld. The whole system is mounted on a self contained portable base. Dimensions of the whole system are 78" lg. x 40" w x 58" h. Jetline Ser. 84166. Very Good Condition

1 ea S412001 Cecil Peck "Dual Position" Outside Corner Seam Welder. This Machine was Used to Tig Weld the Outside Corners of Aluminum, Steel and Stainless Electric Panel Boxes. The Dual Operator Positions were Used for Weld Lengths up to 17" Long. The Air Clamping Device and Copper Mandrel Plates Could be Increased (Within Reason) for Longer Welds. The Torch Carriers are Heavy Duty Variable Speed Devices that are ½ H.P. Dc Motors & Drives. Reconditioned with 2 Cold Wire Feeders or Converted to Mig Welding Including Power Sources

1 ea S505002 Pandjiris Model 24E-3-5-30 24" Weld Seamer. 30" Total Clamping / Welding Length. 3-1/4" Minimum Parts Diameter, 32" Maximum Parts Diameter ( Can be Increased with a Riser ). Rack and Pinion Drive Variable Speed Carriage. Water Cooled Mandrel. Plate Alignment Devices. Jetline Model 9029 Cold Wire Feeder and Model 9033 Pulse Control. Power Supply NOT Included. Serial #400-9364. Good Condition

1 ea S10302 Jetline LWS-24Z, High Production , Automatic Seamwelder. This 1996 Automatic Plasma Welding Seam welder is a High Production Machine that Features: Automatic Clamping & Alignment for Cylinders up to 24" long , 18" to 25" in diameter, and .020 to .187 Thickness, Microprocessor Control, Thermal Arc Ultima 150 Plasma Welding System, Safety Palm Buttons & Guards, and More! Minimum Operator Skill Required, This machine was used for a short run product. Very Low Hours, Excellent Condition

1 ea S701001 Jetline Model LWS-24 24" Seam Welder. 30" total welding/clamping length capacity. 2-1/2" minimum part diameter. 32" maximum part diameter (can be increased with a riser). Gas purge back up bar. Variable speed rack & pinion driven carriage with a model #9027 carriage control. Welding equipment NOT included. Serial #81308 Good Condition

S901029 Jetline Model LWS-36Z Longitudinal Seam Welder. 42” total welding / clamping length capacity. 2.5” minimum part diameter. 32” maximum part diameter (can be increased with a riser). .020 to 3/8” thickness capacity. Variable speed rack & pinion driven carriage with a 9627 carriage control. Plate alignment devices. Water cooled mandrel. 6” x 3.5” manual cross slides. Air torch lifter. Welding Equipment NOT Included !! Serial #060110 “New in 2006!!”Excellent Condition!

1 ea S501001 Jetline LWX-36 "Ultra Precision" Longitudinal Seam Welder. 42" Total Welding/Clamping Length. Minimum Part Diameter Capacity of 3.25", Maximum Part Diameter Capacity of 32" (Can be Increased with a Riser). Welds Material from .005 to 3/8" Thick. Gas Purge Back-up Bar. Continuous Copper Hold Down Fingers. Welding Equipment NOT Included. Serial #7571 Good Condition

1 ea S705005 Jetline LWS-36 36" Longitudinal Seam Welder. 42" total welding / clamping length. Minimum part diameter capacity of 4.5", Maximum part diameter capacity of 32" (can be increased with a riser). Welds material from .020 to 3/8" thick. Gas purge back-up bar. Water cooled mandrel. Welding equipment NOT included. Serial #7991 Good Condition

1 ea S612013 Pandjiris Model 36ES-30 36" Seam Welder. 42" Welding/Clamping Length Capacity. 3" Minimum Part Diameter. 30" Maximum Part Diameter ( Can be Increased with a Riser ). Variable Speed Rack and Pinion Driven Carriage. Water Cooled Mandrel. 6" Manual Cross Slides. Serial #400-8078 Good Condition

S902001 Pandjiris 48” External Seamer. 48” total welding/clamping length capacity. 6.5” minimum part diameter capacity. 30” maximum part diameter capacity. Variable speed rack and pinion carriage. Water cooled mandrel. Welding equipment includes a Lincoln DC-600 power supply and a Lincoln NA-5 sub-arc head and control. Lincoln vertical and horizontal adjusters. Serial #25-1138. Good Condition

1 ea S608005 Hamilton Custom 48" Weld Seamer. 52" Welding/Clamping Length. 6" Minimum Part Diameter. 58" Maximum Part Diameter Capacity. Air Clamping. Side Beam, Carriage and Welding Equipment NOT Included. "AS IS" Condition

1 ea S708003 Berkeley-Davis Model S-2 5’ Weld Seamer. 60" total welding/clamping length capacity. 12" minimum part diameter. 72" maximum diameter. Rack & pinion driven variable speed carriage. Water cooled mandrel. 6" manual vertical and horizontal slides. Welding equipment NOT included. Serial #672548 Good Condition

S903009 Jetline Model LWP-60 5’ Weld Seamer. 66” total welding/clamping length capacity. 5-1/4” minimum part diameter capacity. 32” maximum part diameter capacity (can be increased with a riser). Gas purge back-up bar. Variable speed rack and pinion driven carriage with a digital IPM meter. Welding package includes a Miller Dynasty DX Tig welder, a Cyclomatic AVC-5 arc voltage control, a Jetline CWF-10 cold wire feeder and a 500 amp water cooled machine torch. Serial #8482 Good Condition

1 ea S512003 Webb Model J-68 5’ Seam Welder. 68" total Welding/Clamping Length. 6" Diameter Minimum Capacity. 32" Diameter Maximum Capacity. .020 to .135 Thickness Capacity. Water Cooled Mandrel. Includes a Lincoln TC-3 Variable Speed Travel Carriage, Lincoln NA-5 or NA-3 Control and Head, Lincoln Vertical and Horizontal Adjusters and Lincoln DC-600 Power Supply. 4" Individual Copper Fingers, Copper Back-up Bar. Serial #59115 Good Condition

1 ea S609006 Pandjiris Model 72-ES-52 72" Seamer. 74" Total Welding / Clamping Length. 4" Minimum Part Diameter. 48" Maximum Part Diameter. Equipped with a Variable Speed Model OM-48 Carriage, Vertical and Horizontal Adjusters. Air Actuated Torch Lifter. Spatter Shields. Water Cooled Mandrel. Serial #25-1969. Welding Equipment NOT Included !! Very Good Condition

1 ea S611019P Pandjiris Model #572 72" Weld Seamer. 78" Welding/Clamping Length Capacity. 5" Minimum Part Diameter. 32" Maximum Part Diameter ( Can be Increased with a Riser ). Variable Speed Rack and Pinion Driven Carriage. Serial #25-1046 Good Condition

1 ea S612002P Pandjiris Model #72E6-36 72" Weld Seamer. 78" Welding/Clamping Length Capacity. 5" Minimum Part Diameter. 36" Maximum Part Diameter ( Can be Increased with a Riser ). Variable Speed Rack and Pinion Driven Carriage. Water Cooled Mandrel. Gas Purge Back up Bar. Serial #400-9160 Good Condition

1 ea S505001 Pandjiris Model 72-ES-52 72" Seamer. 78" Total Welding / Clamping Length. 6" Minimum Part Diameter. 52" Maximum Part Diameter (Currently has an 18" High Riser that can be Removed). Equipped with a Variable Speed Carriage, Air Clamping Mandrel, Cable Track and 4" Powered Vertical and Horizontal Cross Slides. Welding Equipment NOT Included !! Serial # N/A Good Condition

S903001 Pandjiris 9’ Weld Seamer. 114” total welding/clamping length capacity. 7-1/2” minimum part diameter. 48” maximum part diameter. Variable speed rack and pinion driven carriage. Water cooled mandrel. 5” x 5” manual cross slides. Rotary slide. Welding equipment NOT included. Serial #25-1875 Good Condition

S807002 Jetline Model LWFS-120Z 10’ Flat Sheet Seamer. 128” total welding/clamping length capacity. 1” Air lift bed for ease of loading. Includes a Jetline SWC-6A carriage with a 9026 control with a digital ipm meter. 2” manual cross slides. Gas purge back-up bar. Welding equipment NOT included. Serial #910315. Good Condition

S807003 Pandjiris Mosel 120-L 10’ Internal/Flat Sheet Seamer. 126” Total welding/clamping length capacity. Variable speed rack & pinion driven carriage with a model M-VSC control. 3” horizontal slide. Water cooled mandrel. Gas purge back-up bar. Welding equipment NOT included. Good Condition

1 ea S704003 Pandjiris Model 120-1/50-FS 10’ Internal / Flat Sheet Seamer. 120" welding/clamping length. .020 to 3/8" clamping range. For flat sheet or I.D. welding on cylinders with a 50" minimum I.D.. Linde model OM-48 variable speed travel carriage. 16.5" mandrel height. 6" wide Pandjiris 4-bar linkage clamp finger arrangement (provides more clamping pressure and inward surge than standard fingers). Gas purge back-up bar. 6" manual cross slides. Welding equipment NOT included. Serial #25-3677 Good Condition

1 ea S207001 Gouran 12 Ft. External or Flat Sheet Longitudinal Sub-Arc Seamer. 144" Total Welding Length. Was used for Welding of Flat Sheet. Can be Used as an External Seamer for Cylinders with a Minimum Dia. of 20". Currently a Maximum Dia. of 36" but can be Increased with a Riser. Linde Rack and Pinion Drive Carriage and Control. Water Cooled Mandrel with Bernard Water Circulator. As Is - Good Operating Condition

1 ea PL612004P Airline Model R40360 Longitudinal Weld Planisher. For Planishing Flat Sheets or Cylinders up to 60" Long. .020 to 3/16" Thickness Capacity on Aluminum or Mild Steel ( 1/8" Maximum Capacity on Stainless Steel ). 10" to 36" Cylinder Diameter Capacity. Serial #R1050 Good Condition

1 ea WS412001 Jetline Portable Heavy Duty Cast Long Length "Stellite" Overlay System. Jetline TKK-24 Precision Screw Drive (1-1/2" screw) Side Beam with 24" Travel. Heavy Duty 9-1/2" Power Vertical Slide, 8" of Z axis Manual Slide. Long Rod Feeder with adj. dia. guide. Miller Oscillator with Center Line Steering. Overall dimensions of Portable side Beam Assy. 76" high, 63" wide, 60" long. System includes Miller 300 amp Synchrowave welder and Tig Torch. Excellent Condition

1 ea SB410001 Mavrix Series 30 2-Axis Side Beam. Motorized 3' X and 3' Y Axes Arms with Automatic Controls that Regulate Travel Direction, Speed and Distance along with Index Direction and Distance. Moves in Any Flat, Straight-line Direction. Both X and Y Axes Have Adjustable Travel Limits and Either Axis can be Used to Index. Standard Weld Travel Speed of up to 45 IPM. Serial #8910883 Good Condition.

1 ea SB507001 Linde 8’ Side Beam Tig Welding System. 10’ Side Beam with a Linde OM-48 Rack and Pinion Drive Variable Speed Carriage for a Total Travel Length of 8’. Portable Floor Mounting Stanchions for a Fixed Height of 59" to the Bottom of the Beam. 4" Manual Cross Slides and a Rotary Slide. Cyclomatic AVC-3 Arc Voltage Control. Miller Weld Oscillator. Jetline CWF-10 Cold Wire Feeder. Good Condition

1 ea SB504001P Jetline Model TKS-96 8’ "Powered Elevation" Side Beam. 124" Side Beam with 8’ of Travel Length. Jetline SWC-3B Variable Speed Travel Carriage. Powered Elevation from 12" to 68" to the Bottom of the Beam. Cyclomatic 4" x 4" Mechanical Seam Tracker. Serial #R4356. Very Good Condition

1 ea SB506001 10 ft. Heavy Duty Custom Side Beam for Sub-Arc or Mig Welding. Welding Length of 10’4". Variable Speed H.D. Rack and Pinion Carriage. Dual 32" Horizontal Manual Cross Slides with 5" Vertical Manual Slides. Cross Slide System has a 6" Pneumatic Lift. Good Condition

1 ea SB609007 Jetline PST-300 Twin Head Overhead Bridge Side Beam. 8’ of Variable Speed Travel on both Carriages Mounted on the Bridge. 12’ Variable Speed Travel on the Side Beam Carriage. 134" to the Bottom of the Side Beam. Welding Torches are Currently Mounted on Dual Powered Slides that have a Total of 60" Vertical Travel. Welding Equipment Includes 2 each Airco Pulse Arc II 550 CV Power Supplies, 2 each Airco Med-40 Wire Feeders, 2 Each Miller Coolmate 4 Water Circulators, 2 each AWC 1,000 Power Assisted Wire Payoff Reels, 2 each Jetline 6" x 6" Automatic Seam Trackers and a Jetline Jetstar Programmable Control. Good Condition

1 ea SB605008 Precision 15’ Side Beam. 12.5’ of Travel by a Variable Speed Rack & Pinion Driven Carriage that runs on Precision Round Way Track. Fixed Height of 52". Lincoln electric Vertical and Horizontal Torch Adjusters. Lincoln NA-5 Control and NA-5R Mig Wire Feed Head. Power Supply Not Included. 460 Volt. Serial #N/A.Good Condition

SB605006 Precision 16’ Side Beam. 13’8” of travel by a variable speed rack & pinion driven carriage that runs on precision round way track. Manual adjustable height from 48.25” to 54.25” in 2” increments. All controls manufactured by Computer Weld Technologies and include a motorized VSA-1000 vertical slide and a HAS-1000 horizontal slide each with a MSC-1000 micro-step control, WF-100 wire feeder with WFD-1000 wire feed control, WRC-1000 weld remote control, DMC-400 carriage control and a WSC-1000 weld sequence control. 460 volt. Serial #n/a. Good Condition

1 ea SB804003 Jetline Model TKMV240 Dual Carriage Side Beam. 240" Length. 2 each Jetline model SWC-6DZ rack and pinion driven variable speed carriages. Mounting stantions and welding equipment NOT included. Serial #969791 Very Good Condition

1 ea SB302001 Pandjiris GB PBT 12 20' Side Beam Welding System. 3 ea. Model 60 Stanchions, VSC-21-12 Variable Speed Carriage, Miller Automatic 1 Head Timers and 4-roll Feed Head, Cyclomatic Seam Tracker, 3 Axis Manual Cross Slides. Pulse Arc Control, This is a Factory Integrated System With all Equipment Mounted and Interfaced on Carriage Good Condition

1 ea SB812002 Bancroft 22’ Side Beam. 20’ travel. Rack & pinion driven variable speed carriage. Mounting stantions and welding equipment NOT included. Good Condition

SB812003 Bancroft 24’ Side Beam. 22’ travel. Rack & pinion driven variable speed carriage. Mounting stantions and welding equipment NOT included. Good Condition

1 ea SB502001 Jetline TK312 26’ Tig Welding Side Beam. 28’ Side Beam with 26’ of Travel, 50" High Floor Mount Stantions and a Jetline Model 9026 Carriage Control with a Travel IPM Meter. Welding Equipment to Include the Following: a Cyclomatic AVC-3 Arc Voltage Control, a Jetline Model 9029 Cold Wire Feeder with a Micro Wire Feed Head, a Cyclomatic 80A Magnetic Arc Oscillator, 5" Manual Horizontal Slide and a 25" Powered vertical Slide. Serial #920516. Excellent Condition

SB905002 Webb Model U-8 34’ Powered Elevation Swing Arm Side Beam. 34’ side beam with a Lincoln model TC-3 travel car for a total of 30’ travel. Powered elevation for a work diameter capacity from 2’ to 8’. Electric/hydraulic powered swing out arms to move the side beam 40” out from the elevation supports for ease of loading and unloading. Serial #67115
Good Condition.

1 ea L604009 Custom 12" GTAW Welding Lathe. 6"-12" Part Length Capacity. 9" Maximum Diameter Capacity. 6" Stroke Pneumatic Tailstock. 5" Pneumatic Torch Lifter. All Functions Controlled by an Allen-Bradley SLC-500 Programmable PLC. Rotary Ground. Welding Equipment Includes a Powcon 150STP Power Supply and a 120 amp Air Cooled Tig Torch. Serial # N/A Good Condition

L501001 WeldLogic CWT-12-15 GTAW Welding Lathe System. CWT-12-15 Variable Speed Headstock with Pneumatic Tailstock, 4" stroke. Arc Length Controlled Vertical Slide. 6" 3-Jaw Self-Centering Chuck. Pneumatic Torch Retract (to rear). Manual Vertical Slide w/ 10" of Adjustment. Manual Rotary Slide for Torch Angle Adjustment. Cold Wire Feeder and Mini Wire Delivery Guide. WP-22 Automatic Tig Torch. Max Part Length – 15", Max Part Diameter – 10-1/2". Serial #9413-014. Very Good Condition

1 ea L708010 Bancroft Model 605 Dual Head Welding Lathe. 14" Maximum length capacity. 14" Maximum diameter capacity. 800 lb load capacity. Variable speed rotation from 1 to 20 RPM. Weld overlap timer. 2 each mig welding heads that each include a Bancroft wire feed system, 4" Vertical and 4" horizontal cross slides and air torch lifters. 120 volt Serial #3565/115-990 Good Condition

1 ea L708011 Bancroft Model 605 Dual Head Welding Lathe. 14" Maximum length capacity. 14" Maximum diameter capacity. 800 lb load capacity. Variable speed rotation from 1 to 20 RPM. Weld overlap timer. 2 each mig welding heads that each include a Bancroft wire feed system, 4" Vertical and 4" horizontal cross slides and air torch lifters. 120 volt Serial #3565/115-990-1 Good Condition

1 ea L708012 Bancroft Model 605 Single Head Welding Lathe. 14" Maximum length capacity. 14" Maximum diameter capacity. 800 lb load capacity. Variable speed rotation from 1 to 20 RPM. Weld overlap timer. Bancroft wire feed system, 4" Vertical and 4" horizontal cross slides and air torch lifters. 120 volt Serial #3558/115-980-1 Good Condition

1 ea L708013 Bancroft Model 605 Single Head Welding Lathe. 14" Maximum length capacity. 14" Maximum diameter capacity. 800 lb load capacity. Variable speed rotation from 1 to 20 RPM. Weld overlap timer. Bancroft wire feed system, 4" Vertical and 4" horizontal cross slides and air torch lifters. 120 volt Serial #3558/115-980 Good Condition

L901028 Jetline Model CW5-192Z Lathe Bed. 5,000 lb weight capacity. Variable speed rotation. 29” minimum to a maximum of 192” length capacity. 60” maximum part diameter capacity. Tailstock is mounted on an electric / hydraulic driven (Includes hydraulic pump system) rack and pinion drive travel car. Side beam and carriage NOT included. Very Good Condition

L809002 Compak-o-matic Model 1027-101 19.5” x 42” Mig Welding Lathe. 19.5” maximum diameter capacity. 42” maximum length capacity. 7” pneumatic torch lifter. 8” stroke pneumatic tailstock. 600 amp rotary ground. Wire feed head. Welding power supply NOT included. Serial #HR149.
Good Condition

L809003 Compak-o-matic Model 1050 20” x 52” Mig Welding Lathe. 20” maximum diameter capacity. 52” maximum length capacity. 7” pneumatic torch lifter. 4” stroke pneumatic tailstock. 4” manual cross seam adjuster. 360 degree torch swivel mount. 2.5” in/out torch adjuster. 600 amp rotary ground. Wire feed head. Welding power supply NOT included. Serial #HG106. Good Condition

L809004 Compak-o-matic Model 1010 20” x 20” Mig Welding Lathe. 20” maximum diameter capacity. 20” maximum length capacity. 7” pneumatic torch lifter. 5.5” stroke pneumatic tailstock. 3” vertical torch adjuster. 2” horizontal torch adjuster. 600 amp rotary ground. Wire feed head. Welding power supply NOT included. Serial #HG-113. Good Condition

1 ea L708009 Bancroft Model 1208 30 Degree Incline Rotary Welder. 800 lb Weight capacity. 44" Maximum Diameter Capacity. Welding bed is fixed at a 30 degree angle. .01 to 10 RPM variable speed rotation. Weld overlap timer. Miller 60 series wire feed system with vertical and horizontal croos slides and an air torch lifter. 120 volt. Serial #3334/110-086 Good Condition

1 ea L608004 Jetline 14" x 14" Mig Welding Lathe. 14" Part Diameter Capacity. 14" Length Capacity. Jetline ZB-100 Positioner, 100 lb Weight Capacity. Air Actuated Tail Stock for Part Clamping. Vertical, Horizontal and Rotary Cross Slides. Miller 300 amp Power Supply. 230/460 Volt. Serial #910424 Good Condition

1 ea L705007 Jetline ZB-100B Benchmaster Welding Lathe. 16" diameter capacity. 17" maximum length capacity. 100 lb weight capacity @ 4" C.G.. Variable speed travel from .1 to 5.0 rpm. 7" diameter 3-jaw self centering chuck. Jetline Model 3018 Base. Jetline 4501A torch holder. Jetline 1016A cross slides. Jetline TS-200B air actuated tailstock. On/off foot pedal. 115 volt. Serial #87401 Very Good Condition

1 ea L601001 Jetline Model CWP-24 90 Degree Power Tilting Lathe Bed. 200 lb Weight Capacity. 20.5" Length Capacity. 12" Diameter Capacity. For use as a Vertical or Horizontal Welding Lathe with a 90 Degree Powered Tilting Bed. 8" Capacity Chuck with a 1/2" thru hole for back purging. 3" Air Actuated Tailstock for Part Clamping. Jetline ALC101-V4T Arc Length Controller. Jetline Model 9024-101 Circumferential Tig Weld Sequencer. Variable Speed Torch Carriage for Either Circumferential or Longitudinal Welding. Powered Torch Lifter. Powered Slides. 115 volt. Serial #920131 Good Condition

1 ea L708007 Bancroft Model 1208 4 Head Welding Lathe. 48" Maximum length capacity. 22" Maximum diameter capacity. 800 lb load capacity. Variable speed rotation from .05 to 10 RPM. Weld overlap timer. 4 each mig welding heads that each include a Miller S-60 wire feed system, Miller Optima 300 pulse pendant, Vertical and horizontal cross slides and air torch lifters. 120 volt Serial #3369-(111-367) Good Condition

1 ea L708008 Bancroft Model 1208 4 Head Welding Lathe. 48" Maximum length capacity. 22" Maximum diameter capacity. 800 lb load capacity. Variable speed rotation from .05 to 10 RPM. Weld overlap timer. 4 each mig welding heads that each include a Miller S-60 wire feed system, Miller Optima 300 pulse pendant, Vertical and horizontal cross slides and air torch lifters. 120 volt Serial #3266-00 Good Condition

1 ea L803015 Weldlogic Model CWT-102 Weld Lathe. 200 lb weight capacity. 13" length capacity. 12" maximum part diameter capacity. 6" diameter 3-jaw self centering chuck. Arc length control. Weldlogic Pulsarc 300-STD DC power supply. Pendant Control. Serial #523 Good Condition

1 ea L804004 Merrick Engineering 64" GTAW Welding Lathe. 12" Maximum part diameter. 64" Maximum part length, 98" side beam with manual spotting car. Merrick Volt Track II arc voltage control. Cold wire feeder, 2" manual cross slides. 360 degree rotary slide. Serial #N/A Good Condition

1 ea L512002 Bancroft High Capacity 3 Station, Dual Torch, Indexing Welding Lathe. 23" Length Capacity, 12" Diameter Capacity. 3 Position Indexing Turret for Loading of Parts, Welding of Parts and Cooling of Parts. 2 Torches for Welding on both Ends of Parts. GMAW Welding Equipment Includes 2 each Miller S-62 Wire Feeders with Tweco Water Cooled Auto Guns on 4" Bancroft Retractable Air Slides. Serial #3327/109-843 Good Condition

1 ea L305001 Bancroft Model VH-24 Welding Lathe. 33" Long x 48" Diameter Capacity. Pneumatic Torch Lifter, Forward and Reverse Variable Speed, Weld Overlap Timer and a Miller 60M Control and Feed Head Serial #3609-(117-212) Good Condition

1 ea L305002 Bancroft Model VH-24 Welding Lathe. 33" Long x 48" Diameter Capacity. Pneumatic Torch Lifter, Forward and Reverse Variable Speed, Weld Overlap Timer and a Miller 60M Control and Feed Head Serial #3610-(117-213) Good Condition

1 ea L206001P Stoody Screw Flight Tig Hard Surfacing Lathe. Capacity of 7" Diameter (may be increased) x 144" Long. This Machine was used for Hard Surfacing with #6 CoCrA Solid Lengths. Has Oscillating Head, Preheat System, Control Console and 500 amp Miller DC Power Supply. Just Out of Service, Good Operating Condition!

1 ea L9912001 Bancroft Welding Lathe. Work Piece Capacity 24" X 72". Bed 12’ Overall, Tailstock has Air Cylinder for part clamping. Linde Automatic Head w/Cross Slides. Variable Speed Rotation For/Rev. As-Is $ 4,950. Re-conditioned to Proper Working Order

1 ea L610002 Jetline Model CWL-72 Lathe and 13’ Side Beam. 500 lb Capacity Variable Speed Headstock / Tailstock. 30" diameter Capacity. 72" Length Capacity (Can Increased to 48" - 120" Capacity with a Spacer). 13’ Side Beam with a Manual Spotting Car that has 12’6" of Travel. Welding Equipment Includes a Jetline Model 9500 System Control, ALC-201V6E ArcLength Control, Rotary Slide and Horizontal Slide. Serial #81322 Good Condition

1 ea L1054413 Melton Model 6330 Single Torch Welding Lathe. Capacity30" dia. X 37" long. Programmable A.B. SLC 500 Control. Pneumatic Fixture Clamping. Miller Maxtron 450 Pulse Welding System with Automatic 1DA Control & Head. Welding system completely integrated. Safety Light Curtain, Operator Console w/Palm Buttons. Automatic Leather Curtains. Hood for exhaust. Complete, ready for your fixturing. "1993" Very Good Condition

1 ea L504001 Custom Built Lathe Type Welding Fixture. Estimated weight capacity 350 lbs. Swing Dia. 48", Tailstock is Power Driven on a Lead Screw to increase the available part length from approx. min. of 19’’ to max. of 60". Variable Speed Rotation by DC Drive with Manual Shift Transmission for Three forward Speed Range and One Reverse. Rotating Welding Ground included. As Is in Working Order

1 ea L610001P Cecil Peck 12’ Welding Lathe. 1,000 lb Weight Capacity. 32" Diameter Capacity. 12’ Maximum Length Capacity. Air actuated Tailstock. Linde Model OM-48 Variable Speed Carriage. Step Over Control. 600 amp Rotary Ground. Through Hole Purge on Tailstock Face Plate. Welding Equipment NOT Included. Serial #N/A Good Condition

1 ea L502001 Centurion Model WL24X168 Welding Lathe. 24" Diameter Capacity. 168" Length Capacity. Variable Speed Travel Car and a Manual Spotting Car. Pandjiris Model "A" 31-1/4" Capacity "Gripper" Chuck. Manual Tailstock Mounted on a Powered Travel Car. Powered Elevation Side Beam. Includes a Lincoln DC-600 Power Supply with a NA-3N Sub-Arc System. Good Condition

1 ea L804002 Jetline CW5-192Z Dual Carriage Welding Lathe. 5,000 lb weight capacity. 56" diameter capacity. 192" length capacity. 12" diameter 3-jaw self centering chuck. 6" pneumatic tailstock. 240" side beam with 2 each model SWG-6DZ rack and pinion driven carriages. Each carriage has an 18" manual vertical slide and a 15" horizontal beam with a manual spotting car. Welding equipment includes 2 each Hobart Arcmaster 501 power supplies with HMC-410 4-roll feed heads, controls and water cooled mig guns. Serial #969791 Very Good Condition

C808012 Cypress CW-5 (CWE-1500) Programmable Circle Welder. For solid wire or flux cored welding process. 1”-12” welding diameter capacity. Variable speed rotation from .3 to 130 ipm. The CW-5 may be used with any CV power supply with connections for 115 VAC and weld contactor. Features include: Wire feed head and control, gun and cable assembly, burnback control, 50’ control cable and gas hose, vertical and horizontal rack adjustment, rise and fall cam with 5” of movement, pre and post flow kit, over lap function and return to start position function. 115 volt. Serial #60707222001A Purchased NEW in June, 2007 – NEVER USED

C808013 Cypress CW-5 (CWE-1500) Programmable Circle Welder. For solid wire or flux cored welding process. 1”-12” welding diameter capacity. Variable speed rotation from .3 to 130 ipm. The CW-5 may be used with any CV power supply with connections for 115 VAC and weld contactor. Features include: Wire feed head and control, gun and cable assembly, burnback control, 50’ control cable and gas hose, vertical and horizontal rack adjustment, rise and fall cam with 5” of movement, pre and post flow kit, over lap function and return to start position function. 115 volt. Serial #60707222002A Purchased NEW in June, 2007 – NEVER USED

1 ea C608003 Compakomatic Model 1025 Rotomatic Mig Weld-A-Round. 0 to 6" Diameter Capacity. Manual Adjustable Height. Variable Speed from .30 to 15 RPM. Adjustable Rotational Overlap from 0 to 360 Degrees. 6" Air Torch Lifter. Model 375 Rotational Control. 600 amp Current Capacity. Miller 300 amp Power Supply. Serial #GM-154 Good Condition

1 ea C804006 Compakomatic Model 920E Weld-a-Round. 8" maximum part diameter. 13" maximum part height (can be increased with a riser). 7" pneumatic torch lifter. Compakomatic series 400 control. 115 volt. Serial #GM241 Good Condition

1 ea C604008 Machine Technologies GTAW Weld-a-Round. 12" Part Diameter Capacity. 6" Part Height Capacity (Can be Increased with a Torch Riser). 1" Vertical Torch Lifter. Weld Over Lap Timer. All Functions Controlled with a Programable PLC. Welding Equipment Includes a 1994 Miller Maxstar 152 with Snap Start, Miller Water Circulator and a 250 Amp Water Cooled Tig Torch. Serial #1-549-2 Good Condition

1 ea C508001 Rumble Automation Weld-A-Round Circular "Spud" Welding Station. 5" Vertical Stroke. Variable Speed Torch Rotation by a 3 Turn Potentiometer. 36" High Work Table. 32" Part Diameter Capacity. 6" Diameter Weld Capacity. Currently Equipped with a Hobart Auto-CVS Wire Feeder. Power Supply NOT Included. 575 volt. Serial #100-64-3712 Good Condition

C810002P Bancroft Weld-A-Round 300 Circular “Spud” Welder. The Weld-A-Round 300 is the most popular stationary circular welding system in the welding industry. 300 Amp ground capacity. 75 lb clamping force. 8” vertical stroke. 0.7 to 14 RPM travel speed. 24” diameter round table. Welding equipment NOT included. Serial #n/a Good Condition

1 ea C612015 Bancroft Weld-A-Round 300 Circular "Spud" Welder. The Weld-A-Round 300 is the most Popular Stationary Circular Welding System in the Welding Industry. 300 Amp Ground Capacity. 75 lb Clamping Force. 8" Vertical Stroke. 0.7 to 14 RPM Travel Speed. Welding Equipment NOT Included. Serial #50359-10 Good Condition

1 ea C612014 Bancroft Weld-A-Round 300 Circular "Spud" Welder. The Weld-A-Round 300 is the most Popular Stationary Circular Welding System in the Welding Industry. 300 Amp Ground Capacity. 75 lb Clamping Force. 8" Vertical Stroke. 0.7 to 14 RPM Travel Speed. Equipped with rise and fall option. Welding Equipment NOT Included. Serial #50123-01 Good Condition

1 ea C609008 Bancroft Weld-A-Round 300 Circular "Spud" Welder. The Weld-A-Round 300 is the most Popular Stationary Circular Welding System in the Welding Industry. 300 Amp Ground Capacity. 75 lb Clamping Force. 8" Vertical Stroke. 0.7 to 14 RPM Travel Speed. Bench Mounted. Welding Equipment NOT Included. Serial #N/A Good Condition

1 ea C512001 Bancroft 350 High Capacity Dual Head, 3 Station Indexing Weld-a-Round. Bancroft is the Manufacturer of the Most Popular Stationary Circular Welding System in the Welding Industry. Both Weld Stations have 8" Vertical Stroke with a 150 lb Clamping Force and Variable Speed Torch Rotation from 0.7 to14 RPM. 300 amp Capacity. A 3 Position Indexing Table for Loading of Parts and Welding Under 2 Separate Weld Stations. Can be Used for 2 Passes on One Part or One Pass on Two Individual Parts with Proper Fixtures. Currently Set up for GTAW Application. Serial #3300/109-003 Good Condition

1 ea C501001 WeldLogic CWT-12-15V Vertical Welding Positioner. Precision Vertical Positioner with Self-Centering 3 Jaw Chuck, 6" Dia. Torch Holder Post with Pneumatic Torch Retract. 100 lb Capacity. Serial #CWT-12SN9413 Very Good Condition

1 ea C412001 Alloy Custom Circular Welder. 75 lb Capacity, Variable Speed (0.8 – 50 RPM) 4" 3-Jaw Chuck, Lever Actuated Gravity Type Part Hold Down Mounted on 6" Slide. 6" Maximum Part Diameter, 6" Maximum Part Height. 3 Axes of Torch Adjustment. Analogue Weld Control – 10 Turn Potentiometer for Accurate Speed Control, Start/Stop w/ E-Stop, Forward/Reverse. Manual Flip-down 4" x 5" Shaded Lens for Weld Viewing Good Condition

1 ea C205002 Alltra Corporation Model VWL2436 Circular Welder. Vertical Lathe with an 18" Part Diameter Capacity, 24" Part Length Capacity and an Air Actuated Centering Head. A Complete System that Includes a Lincoln DC-400 CC/CV Power Supply, Lincoln NA-5R Head and Control with a Lincoln Analog Interface Procedure Control, Miller Coolmate 4 Water Circulator, 20" Motorized Horizontal and Vertical Cross Slides, Allen-Bradley SLC5/04 Control and Allen-Bradley Panelview 1400 Monitor with Operator Friendly Touch Screen Programming. Manufactured in 1998. Serial #2211 Excellent Condition

1 ea C805022 Cecil Peck Circular Welder. Hand Wheel Table Lift. 1 to 6" welding diameter capacity. 43" part diameter capacity. Variable Speed Rotation. Pedestal Control Console for all Functions. Welding equipment NOT included. Serial #n/a. Good Condition

1 ea C406001P Cecil Peck Circular Welder. Manual Table Lift. No Table. 1" to 6" Diameter Capacity. Variable Speed Rotation. Pedestal Control Console for all Functions. No Welding Equipment. Serial #N/A As Is Price

1 ea C204001 Cecil Peck Circular Welder. Hand Wheel Table Lift. 36" x 30" Tee Slotted Table. Variable Speed Rotation. Pedestal Control Console for all Functions. Equipped with a Lincoln NA-2 Submerged Arc Control and Welding Head and a R3S-600 Power Supply. Serial #69203 Good Condition

1 ea TW303003 Arc Machines Model M-115 Orbital Pipe Welding Power Supply. 300 amp, 60% duty cycle, 230/460, 3-phase, Built in Water Re-circulating Unit. Current Pulse, Wire Pulse and Weld Oscillation Controls Fair Condition, As Is Only Price

1 ea TW1011002 Arc Machines Model 215, Orbital Tube to Tube Welder. Includes: Model 215- OP Operator Control, Cables etc. Weld heads NOT Included ! Ser. #4074 "1988" Exc. Condition!

1 ea ARC 109 1 Arc Machines, Inc. Model 109-1, Tube to Tube Welder. "1982" Ser.# 513, Includes: 1 ea 09-1000 Head for 1" Max. Dia. Tube. Built-In Water Re-Circulating Unit. As-Is Only !! Good Condition

1 ea ME612008 George Fischer Model RA-2 Pipe Cutting / Beveling Machine. Outside Diameter Range from ¼" to 2" Pipe, Wall Thickness up to .217". Cuts Square to Within .005". 115 Volt. Serial #30394 Good Condition

1 ea TW303004 Protem Model US-38 Pipe Beveling Machine. Capacity from 1.57 to 8" I.D..Manual Feed of 2". 2 H.P. Standard Air Motor Drive. For Beveling, Facing, Counter Boring and Deburring. Serial #38076 Good Condition

1 ea ME506001 Protem Model US-38 Pipe Beveling Machine. Capacity from 1.57 to 8" I.D.. Manual Feed of 2". 2 H.P. Standard Air Motor Drive. For Beveling, Facing, Counter Boring and Deburring. Serial #N/A Good Condition

1 ea TW209002 Tri-Tool Model 202TS. Pneumatic Tube to Tube Sheet Facing Tool. Complete with Collets for Tubing from .77 to 1.95 I.D. Serial #1197007 Good Condition

1 ea ME606007 Tri Tool Model 572E Tube Squaring Machine. ¼" to 2" Tube Diameter Capacity. 115 volt. Serial # N/A Good Condition

1 ea ME606010 Tri Tool Model 574E Tube Squaring Machine. 1" to 4" Tube Diameter Capacity. 115 volt. Serial #1194067 Good Condition

1 ea ME606015 Mathey Dearman Model 48 Porta-Mill Portable Pipe Cutting & Beveling Machine. 3.375 to 8.125 I.D. Pipe Diameter Range Capacity. ½" Maximum Face or Bevel Capacity. Power Unit NOT Included. Works with Rothenberger USA, Mini-Collins and Ridgid Universal Power Drives. Serial # N/A Good Condition

Any GEN PT200B DIY S 06 NEW Gentec Type S Circular Welding System. A Gentec 330 lb capacity @ 2" c.g. positioner, Variable speed rotation from0 to 4.0 RPM, 90 degree manual hand wheel tilt mounted on a DIY-S-06 accessory kit that includes a CB-002 control, 24" base rail, 20" mounting rail, adjustable torch holder with 2" cross slides and pneumatic torch lifter. Mounted on the positioner is a 19-5/8" capacity 3-jaw self centering chuck. 115 volt. NEW !!

WS809001 Compak-o-matic Model 440A 6” Linear Dual Torch Mig Welding System. 6” maximum welding length. Dual torch with up to 13” between the torch heads. 6” manual in/out slide for fine adjustment. 3” manual right/left fine adjuster. 6” stroke in/out indexing table for loading and unloading. System includes 2 wire feeders and system controller. Welding power supplies NOT included. Serial #GY211. Good Condition

WS901022 Pandjiris Stationary Manipulator Arm and Unit Frame Turning Roll System. A Pandjiris stationary manipulator arm with a fixed height of 45.5” under the arm and a length capacity of 40’. The turning rolls have a 68,000 lb turning capacity. 7’ to 14’ diameter capacity with a fixed axel center of 72”. Variable speed rotation. 5 sets of 5” wide x 20” diameter rubber wheels spaced over the 30’ length of a variable speed travel car that runs on 69” gauge rail track. Welding equipment can be mounted on the end of the manipulator arm for internal longitudinal or circumferential welding on cylinders. 460 volt. Serial #n/a. Good Condition

WS901021 Pandjiris Stationary Manipulator Arm and Unit Frame Turning Roll System. A Pandjiris stationary manipulator arm with a fixed height of 45.5” under the arm and a length capacity of 40’. The turning rolls have a 68,000 lb turning capacity. 7’ to 14’ diameter capacity with a fixed axel center of 72”. Variable speed rotation. 5 sets of 5” wide x 20” diameter rubber wheels spaced over the 30’ length of a variable speed travel car that runs on 69” gauge rail track. Welding equipment can be mounted on the end of the manipulator arm for internal longitudinal or circumferential welding on cylinders. 460 Volt. Serial #66-4595. Good Condition

WS901027 Jeline HWP-50D Hot Wire Process Tig System. A complete Jetline hot wire system consisting of : Model HWP-50D contoured-wave hot wire power supply, Model 9629HW power control, Model HWF heavy-duty wire drive unit, Model 9302B wire feed speed control, hot wire torch and hot wire torch positioned assembly. A complete integrated package with all necessary inter-connecting cables and hoses. Serial #010812. Very Good Condition

1 ea WS704015 Hobart Manipulator / Positioner TIG Welding System. Includes a 1,500 lb capacity @ 4" C.G. positioner with power tilt and variable speed rotation. Positioner is mounted on a manual travel car with 2’ travel. Manipulator has powered lift from 30" to 90", manual reach from 35" to 59" from the center of the mast. And a 6" horizontal adjuster. Current welding equipment includes a Jetline model ALC- 401-6 Arc Length control and model 9629 controller and a Jetline CWF-10A cold wire feeder. All equipment mounted into a single skid frame base. Serial #41-1641. Very Good Condition

1 ea WS703010 Cissel 12’ x 4’ Submerged Arc Welding Gantry. 12’ variable speed rack and pinion driven carriage. 4’ variable speed Lincoln TC-3 carriage on the cross boom. Complete Lincoln NA-5 sub arc package. Serial #111978 Good Condition

1 ea WS702002 Weldlogic Positioner/Tig Welding System. A Weldlogic 200 lb capacity positioner with a 12" capacity chuck integrated with a Weldlogic complete GTAW welding system. Welding system includes a Weldlogic RPW-2000 power supply, Weldlogic cold wire feeder, Weldlogic arc length control, Weldlogic weld oscillator and pendant control for programming all functions. 230 volt. Serial #9914760 Good Condition

1 ea WS702003 Weldlogic Positioner/Tig Welding System. A Weldlogic 200 lb capacity positioner with a 12" capacity chuck integrated with a Weldlogic complete GTAW welding system. Welding system includes a Weldlogic RPW-2000 power supply, Weldlogic cold wire feeder, Weldlogic arc length control, Weldlogic weld oscillator and pendant control for programming all functions. 230 volt. Serial #9730194 Good Condition

1 ea WS604010 "1996" Weldline / Miller GTAW Circular Welding Station. Weldline Automation Model WA-2 200 lb Capacity Positioner with a ½" to 16" Capacity 3-Jaw Chuck, Weldline 6" Arc Length Control, Weldline Weld Sequence Control, Weldline Cold Wire Feeder, 4" Manual Cross Slide and Rotary Slide. Pneumatic part Clamping. Welding equipment Includes a Miller XMT-304 Inverter Power Supply, Miller HF-251D-1 High Frequency Arc Starter, Miller PC-300 Pulse Control, Tweco TC900 Water Circulator and a Weldcraft WP-27 500 amp Water Cooled Tig Torch. Serial # N/A Good Condition

1 ea WS601002 Arc Systems Automatic Pipe Welding System. System Includes a Preston-Eastin HS-2S 2,000 lb Capacity @ 6" C.G. Headstock with a 20" Diameter Scroll Chuck that has a 6-1/2" Thru Hole. A Weldlogic AWS-150 Advanced Tig Welding System that Includes Controls for Variable Speed Rotation of Headstock, Weld Current Control, Arc Distance Control, Cold Wire Speed Control and Feeder and a 1.0 to 150 amp DC Power Supply. 3 eacg 6" Manual Slides for 3 Axis Adjustment of Torches. All Controls are Mounted in a Single Remote Pendant Control. 230/460 Volt. Serial #HS2S-13 Good Condition

1 ea WS509001 Pandjiris "1998" Hot Wire Tig Pipe Welding Station. A Complete Hot Wire Tig Pipe Welding Station that Includes a Pandjiris 4’ x 4’ Manipulator on Travel Car, 2 each Pandjiris HS-20PE-VS Headstocks with TJ-20 Chucks, Pandjiris Pipe Supports on Manual Travel Cars, Miller / Jetline Welding Package and a Complete set of 50’ Tracks. Please Ask for a Detailed Specification Sheet. Excellent Condition

1 ea WS507001 Mark Five Manipulator/Turntable System. Turntable : 1,000 lb Capacity, 20" High. 24" Diameter Table with Slots. Variable Speed Drive from .01 to 1.4 RPM. The Manipulator if Fixed Over the Turntable with a Manual Lift of 34" from 5.25"and a Manual Reach of 24". Serial #JN-1189 Good Condition

1 ea WS404001 Ransome Positioner / Manipulator / Sub-Arc Welding System. System Includes a Ransome 5P 500 lb Cap. @ 6" C.G. Positioner (Ser. #1314851) with Power Tilt, Variable Speed Rotation and Manual Height Adjustment. A 3JC40 40" Diameter 3-Jaw, Self-Centering Welding Chuck. A Ransome Model 99 Manipulator (Ser. #9526562) with 72" Power Elevation from 0 to 71" at the Torch, Fixed Boom with a Manual Spotting Car from 44" to 88" from Center of the Mast, Manual Mast Rotation. A Complete Lincoln DC-600 Sub-Arc System with NA-5 Control, Weld Head And A Invincible Flux Recovery System. Very Good Condition

1 ea WS406001 Pandjiris Model SWPT-102 Dual Side Beam Stiffener Welder. HD Welding Carriage, variable speed (0 – 200 IPM). Twin Cyclomatic Seam Tracking systems to locate torches on opposing sides of stiffener. Open-End Gantry Style Yoke with 96" of Weld Length allows loading of stiffener from one end. Advancement of sheet is readily done with help from pneumatic plate lift rollers that automatically lift part off back-up bar between welds. 15 Pneumatic hold down Clamps and Part Locators designed to automatically locate and hold "I" or "U" shape stiffener in place on sheet. No tooling or jigs necessary for part alignment. Back-up Bar for heat sink and part distortion control. System is capable of feeding Aluminum or Steel Wire using GMAW Process. Twin 180 degree water-cooled GMAW torches for high production. Remote Control Podium. Was used for welding stiffeners for aluminum dump truck beds and bodies. Very unique piece of equipment – Must See!!! Very Good Condition

1 ea WS411001 Linde PTA Surfacing System / 5 x 6 Manipulator. A Complete Linde Plasma Transfer Arc Weld Surfacing System that Includes a C75-500 (500 amp, 60% Duty Cycle) Power Supply, PTA Gun, Automatic Powder Feeder, 12" Manual Vertical Adjuster, and a Linde Solid State Weld Oscillator. Gun, Vertical Adjuster, Powder Feeder and Oscillator are Mounted on a Linde OM-48 Variable Speed Travel Car that Runs on a Fixed Boom Manipulator with 6’ of Horizontal Travel and 60" of Vertical Travel from 31" to 91" by a Screw Driven Manual Hand Wheel Lift. Good Working Condition

1 ea WS404007P Aronson/Jetline Manipulator/Positioner/Dabber Welding System. A Complete System That Includes an Aronson Model G6MR6ML-PK 6' x 6' Manipulator (Serial #73151) with 6' Variable Speed Reach fron 14" to 86" from the Center of The Mast Rotation, 6' Constant Speed Lift from 29" to 101" to the Bottom of the Boom. 111.5" Overall Height. Manual Mast Rotation. Mounted on a 72" Portable "X" Frame Base. The Welding Equipment Mounted on the Manipulator Includes a Jetline ALC101-V6T 6" Arc Length Control, a Jetline 9029 Cold Wire Feeder Control, a 9033 Wire Pulse Control and a Jetline Mechanical Dabber System. Welding Heads are Mounted on a 30" Extension which has a Manual 180 Degree Vertical and Horizontal Angle Adjuster. Welding Equipment Mounts Over the Top of an Aronson Model D5-GP100 Positioner (Serial #72299) 825 lb Capacity @ 6" C.G., Manual Tilt, Variable Speed Rotation, 31" Round Table With Slots at a Fixed Height of 31". All Equipment Calibrated in February, 2003 Good Condition

1 ea WS408001 Compak-o-Matic Rotary Welding Station. System Includes a Ransome B-100, 100 lb Capacity Welding Positioner, A Compak-o-Matic PC-300, 300 amp CV Power Supply, a Model 320 Wire Feed System with a Machine Torch, 8" Horizontal and Vertical Torch Adjusters, and Model 263 Control Module with Weld Time Function. Serial #1530 Good Condition

1 ea WS999001 Linde/Jetline HWC-7 Cold Wire Tig System. Jetline ZB-100 Positioner on moveable screw drive base. Complete with HW-500SS Welder, Auto Controls, Cross Slides and Floor Standing Base. Excellent Condition

1 ea WS006003 Hobart/Aronson 2 Station Automatic Spud Welder. Mig Welds Rings up to 12" Diameter, Two alternate weld stations w/ Air Clamping of parts. Control Console w/ Station Selection. Many Tooling Fixtures. Var. Speed Rot. by 2 Aronson positioners. Includes Hobart Dual Wire Feeder, Torches and Welder. Complete System Ready to Weld

1 ea RC505001 "2003" Panasonic 3 Axis Model ISP Cartesian Robotic Tig Welding Cell. Initially powered up in November 2003 this cell was used off and on for approximately 8 months before the application was discontinued. This Panasonic Model ISP Cartesian Robot, has approx. 43" (x) horizontal movement, 15" (y) vertical movement and 21" (z) horizontal movement. There is also a 2 axis clamping fixture or tooling table. The complete welding package on this cell includes Two (2) Water Cooled Tig Torches with manual adjustable separation of the torch holders on one axis, Two (2) Panasonic YC-500WX4 Power Supplies completely integrated with all regulators, hoses, cables etc. Water supply required. The welding cell is 75" wide x 103" high x 145" deep and has a complete safety package including, Powered Safety Screen, Light Package, Front Operating Control and Palm Buttons. This cell could be changed to the Mig welding process. This is a late model, low hour, system in Excellent Condition

1 ea RC505002 "2003" Panasonic 4 Axis Model ISP Cartesian Robotic Tig Welding Cell. Initially powered up in November 2003 this cell was used off and on for approximately 8 months before the application was discontinued. This Panasonic Model ISP Cartesian Robot, has approx. 17 1/2" (x) horizontal movement, 10" (y) vertical movement and 15" (z) horizontal movement. The Fourth Axis is a Rotating Wrist movement for the Torch Holding Device. This Cell also includes a Horizontal Moving Fixture/Tooling Table Integrated with the Robot from the Load/Unload position to the Robotic Welding Position. The Complete Welding Package on this cell includes one (1) Panasonic YC-300WX4 Power Supply and One (1) Water Cooled Tig Torch completely integrated with all cables, hoses, etc. Water supply required. The welding cell is 75" wide x 103" high x 126" deep and has a complete safety package including, Powered Safety Screen, Light Package, Front Operating Control and Palm Buttons. This cell could be changed to the Mig welding process. This is a current model, low hour, system in Excellent Condition

1 ea RC505005 "2003" Panasonic VR-008 GII Robotic, 6 Axis Tig Welding Cell. This is a larger, panel constructed, Robotic welding Cell with a large Fixture/Tooling table that has approx. 78" of in and out movement between load and welding stations. The Complete Welding Package on this cell includes one (1) Panasonic YC-300WX4 Power Supply, One (1) Water Cooled Tig Torch complete with all cables, hoses, etc. Water supply required. This Welding Cell accomodated this Panasonic VR-008 GII Robotic System and the "2003" Motoman UP-50 listed and priced separately below. See the picture of this larger panel constructed cell for approximation of size. This is a Current Model, Low Hour System, in Excellent Condition! Price includes Panel Constructed Cell.

1 ea RC505004 "2003" Panasonic Robotic VR-008 GII, 6 Axis Tig Welding Cell. The Fixture/Tooling Platform is on an Integrated Horizontal Travel Part Presentation Carriage with 26" of Movement from the Load/Unload Station. This system provides maximum operator access for load/unloading and increased productivity. The Complete Welding Package on this cell includes one (1) Panasonic YC-300WX4 Power Supply, One (1) Water Cooled Tig Torch complete with all cables, hoses, etc. Water supply required. The welding cell is a completely enclosed 102" wide x 103" high x 172" deep structure with side access doors and a complete safety package including, Powered Safety Screen, Light Package, Front Operating Control and Palm Buttons.
This is a Current Model, Low Hour System, in Excellent Condition!

1 ea R510001P Motoman Model YRFL-NND10G 6-Axis Robot. 22 lb Payload Capacity. Robot Controller NOT Included. "1986" Serial #RH9963-6047-8 "As-Is" Only

1 ea R510011P Miller/OTC Model MRV-6 6-Axis Welding Robot. 13.2 lb Payload Capacity. 55.2" Reach. Includes a Miller Model C-1 Control Cabinet. Welding Equipment NOT Included. "1991". 190-575 Volt. Serial #KB168739 "As-Is" Only

1 ea R510012P Miller/OTC Model MRV-6 6-Axis Welding Robot. 13.2 lb Payload Capacity. 55.2" Reach. Includes a Miller Model C-1 Control Cabinet. Welding Equipment NOT Included. "1992". 190-575 Volt. Serial #KC301838 "As-Is" Only

1 ea WS605013P Cybotech Automatic Manipulator / Positioner Tig Welding System. System Includes A Fabspec 2,500 lb Capacity Positioner, a 6 Axis Cybotech 4’ X 3’ Manipulator / 6’ Travel Car, Cybotech RC-6 Controller, Cold Wire Feeder, Miller Syncrowave 300 w/ SP-4 Pulser. System Offers 9 Axis of Powered Movement. Good Condition

1 ea WS605014P Cybotech Automatic Manipulator / Positioner Tig Welding System. System Includes A Fabspec Model 1840 2,000 lb Positioner, a 6 Axis Cybotech 4’ X 3’ Manipulator / 6’ Travel Car, Cybotech RC-6 Controller, Cold Wire Feeder, Cybotech EPU Power Supply. System Offers 9 Axis of Powered Movement. Good Condition

1 ea RP612017 Preston-Eastin Model RHSDS-5 Dual Sided Robotic Headstock/Tailstock. Dual sided for loading / unloading on one side while welding on the other. Shot pins for precise positioning. 500 lb balanced load capacity on each side. 6’ length capacity. 24" diameter capacity. Dual Allen-Bradley SLC-150 controls, one for each of the headstock/tailstocks. Serial #RHDS-5-6 Good Condition "As-Is" Only

1 ea RP612018 Preston-Eastin Model RHSDS-5 Dual Sided Robotic Headstock/Tailstock. Dual sided for loading / unloading on one side while welding on the other. Shot pins for precise positioning. 500 lb balanced load capacity on each side. 6’ length capacity. 24" diameter capacity. Dual Allen-Bradley SLC-150 controls, one for each of the headstock/tailstocks. Serial #RHDS-5-10 Good Condition "As-Is" Only

1 ea RP004002 ABB/Esab Orbit 160B, Robotic Positioner. Two Station Articulating Positioner, for Load & Weld Station. 353 lbs Each Side, Table Rotation 90 Deg. in 2.7 Sec. Or 360 Deg. in 6.8 Sec., Tilting Arm: Turning Speed 0 to 11.8 RPM, Indexing 90 Deg. 2.7 Sec., 360 Deg. 7.2 Sec., Station Interchange 3.5 Sec. This unit was integrated to ABB/Esab a IRB 6L2 Robot. Pos. Ser.#414 441 9034, Cont. 443 440 9005

1 ea RP307001 Aronson Ride-5, Double Ended Tilt and Rotate Robotic Indexing Positioner. This Two-Station Tilt/Rotate Positioner has a Capacity of 500 lbs per Table @ 6" C.G. Tilt and 3" C.G. Rotation. 180 Degree Sweep in 7 Seconds with .0001 Repeatability. Two 18" Diameter Tables with Slots. 8 Non-Adjustable Index Stops for the Table Rotational Axis. 4 Non-Adjust6able Index Stops for the Tilt Axis. Can be Connected to any Robot with Compatible I/O. This is an Indexing Type System, Not Servo. Serial #843 Good Condition

1 ea RP210003P Koike-Aronson RHS10/T2.5-30SD Robotic "Skyhook" Positioner. 2500 lb Load Capacity. Center of Gravity 28". Overhang 3". Off-Center 38" Table. Backlash Control and "Zero" Indicator on Control. "Skyhook" Positioners Provide Part Rotation in Two 360 Degree Axis which Result in Partial or Full Inverting of the Work piece. Serial #869 Very Good Condition

RP207001 Preston-Eastin Model DEPA-30FBRobotic Positioner. . Two Station Articulating Positioner, for Load & Weld Station. 3,000 lb Capacity @ 6" C.G. Each Side. Fixed Table Height of 48" with the Table Flat. 43" x 43" Square Work Tables. Servo Drive that can be Installed on any Robotic System with the Proper Relays. "1996" Serial #DEPA-30FB-187 Priced As-Is !! Ready to Install Your Servo Motors and Controls!! Very Good Condition

RP809023 Aronson RDE-RHS10/T3-42SD Double Ended Robotic Skyhook Positioner. A two station articulating positioned for loading and weld station. Each side has a capacity of 3,000 lb @ 18” c.g., 12” off set tables from the center of the horizontal rotational axis. 36” diameter round tables with 8.25” thru holes. Serial #882. AS-IS Only !!

RP809024 Aronson RDE-RHS10/T3-42SD Double Ended Robotic Skyhook Positioner. A two station articulating positioned for loading and weld station. Each side has a capacity of 3,000 lb @ 18” c.g., 12” off set tables from the center of the horizontal rotational axis. 36” diameter round tables with 8.25” thru holes. Serial #881. AS-IS Only !

1 ea RP309001P Koike-Aronson "1994" Model #RDCG/T6-100/26SD "Drop-Center" Positioner. Tilt Capacity of 6600 lbs @ 24" from the table, or 4000 lbs @ 57", or 2000 lbs @ 90"!!. Rotation Capacity of 6600 lbs @ 20" Center of Gravity off of the centerline of rotation. Inside Distance Between Upright Sides is 101-3/4" Both Tilt and Rotation Axis have Adjustable Anti-Backlash Dual Pinions on Bull Gears! Both Axis are Servo Drive Variable Speed with Encoders and Resolvers. 360 deg. Rotation @ 0.0-2.0 RPM, 200 deg. Tilt @ 0.0-1.75 RPM. (This Servo Drive Positioner can be converted to a Manual Pendant Operated Machine). Table is 48" x 48" with Hydraulic Master Clamping System for Slave Pallet Mounted Tooling 1 ea. slave included . Note; "Drop Center Positioners" are typically used for work pieces with longer Center of Gravity distances from the table, resulting in lower working or welding heights than using higher capacity positioners. This 1994 Machine has NEVER BEEN USED! Brand New Condition!

6 ea AA310001 Computer Weld Technology ADM III Arc Data Monitoring System. The CWT Arc Data Monitor is a Self-Diagnostic Microprocessor System Designed to Provide Quality Control for Arc Welding Applications. Each System Includes Sensors and Cables to Monitor the Following Parameters: Arc Voltage from 0 to 100.0 Volts DC + or - 1%, Arc Current from 0 to 1000 Amps DC + or - 1%, Gas Flow from 5 to 255 scfh + or - 1% and Travel Speed from 1 to 100 ipm + or - 3% Very Good Condition

7 ea AA310002 Computer Weld Technology ADM III Arc Data Monitoring System. The CWT A rc Data Monitor is a Self-Diagnostic Microprocessor System Designed to Provide Quality Control for Arc Welding Applications. Each System Includes Sensors and Cables to Monitor the Following Parameters: Arc Voltage from 0 to 100.0 Volts DC + or - 1%, Arc Current from 0 to 1000 Amps DC + or - 1% and Gas Flow from 5 to 255 scfh + or - 1% Very Good Condition

1 ea SP503002 Sciaky 50 KVA Three Phase Press Type Spot Welder. Type PMC02ST Machine # 4540 Throat 10" x 36" with 8" extensions for a max. of 44". This machine has a Medar Three Phase Control Model Legend F.W.F.C. Ser. # 100-552 Dwg. ES-83069. Very Good Condition

1 ea SP103523 Taylor Winfield 70 KVA, Equalizing Rocker Arm Welder. "1996" Very Little Use! Mach. #960180. 70 KVA, 460V. 20"Depth, Water Cooled, Self Equalizing Arms, High Production System with Quick Manual Part Indexing for Rotation and Forward- Back Feed. These machines (we have 3) were designed for production welding of washer/dryer tubs. "1996" Excellent Condition

1 ea SP103524 Taylor Winfield 85 KVA, Equalizing Rocker Arm Welder. "1996" Very Little Use! Mach. #960177. 85 KVA, 460V. 20"Depth, Water Cooled, Self Equalizing Arms, High Production System with Quick Manual Part Indexing for Rotation and Forward- Back Feed. These machines (we have 3) were designed for production welding of washer/dryer tubs. "1996" Excellent Condition

1 ea SP103525 Taylor Winfield 85 KVA, Equalizing Rocker Arm Welder. "1996" Very Little Use! Mach. #960179. 85 KVA, 460V. 20"Depth, Water Cooled, Self Equalizing Arms, High Production System with Quick Manual Part Indexing for Rotation and Forward- Back Feed. These machines (we have 3) were designed for production welding of washer/dryer tubs. "1996" Excellent Condition

1 ea SP405001P Automation International Inc., "1998" 200 KVA Resistance Seam Welder. This Machine was a Repo by the bank 18 months after it was new and has Extreme Low Hours of Use! Like New Condition! Model SG-18-CG Ser# 50452-100. 440 input, Max. Sec. Amps 38300 @ 18" Sec. Volts 4.58 – 12.9. Control Volts 115. Weldtronic/Technitron (WTC) Control WT-500 Type W5. Ser# WT/112987-1 Copper Wheels 12" dia. by ½" Thick. Throat Depth 18-1/4". INCLUDES, Schreiber Engineering Corp. 3 ton Cooling Unit. Model #300AC, Ser.# 4127 Voltage 460/3 Phase. Great Value of a Like New Machine!

1 ea PW310001 Thermal-Arc PS-3000 Plasma Welding System Complete. Each System to Include the Following : PS-3000 Power Supply with an Output Range from 5 to 350 amp 300 amp 60% Duty Cycle 208/230/460 volt 1 or 3 Phase, WC100B Weld Control Console, HE-100A Water Cooler, Weld Sequence Package with WT-1 Weld Timer, Cs-1 Current Sloper and CP- Pulser, #870119 Interface Cable and a 180 degree Offset Model 4A 12.5' Plasma Machine Torch, 220 amp, 60% Duty Cycle Very Good Condition

PW310002 Thermal-Arc Ultma 150 Plasma Welding System. A Self Contained Package with a 150 amp, 50% Duty Cycle Power Supply, Coolant Circulator and Control Console. 200-460 VAC, 1 or 3 Phase, Welding Torch NOT Included. Optional Sequencer console with timer, slope, pulse is available, price upon request. Excellent Like New Condition Condition $ 4,250.00 - Optional Weld Sequencer Timer, Pulse, Slope

1 ea PS709004P Metco Model AR-2000 6-Axis Thermal Spray Robot. A complete robotic system that includes a Metco AR-2000 6-axis robot with controller, a Metco teach pendant, a Metco R-2 operating box and a set of connecting cables. Serial #AR110001 AS-IS Only

1 ea PLA PS61S Plasmatron Model PS-61S Plasma Power Supplies. Ser.# JD-683762 & Ser.# JC- 586408, 1000 amps @ 40 volts or 500 amps @ 80 volts, 74 K.V.A., Input 200/230/460 Power Factor Corrected. Very Good Condition

CM904011 Linde Model CM-45 Track Cutting Machine. Variable speed friction driven carriage. 4.25” to 20.5” adjustable reach 3 sections of 6’ track. Cutting torch NOT included. 120 volt. Serial #2X2 Good Condition

CM904010 Linde Model CM-79 Track Cutting Machine. Variable speed friction driven carriage. 4.25” to 20.5” adjustable reach 3 sections of 6’ track. Includes oxygen/acetylene machine cutting torch. 120 volt. Serial #75AO1374 Good Condition

CM809007 Bug-O Uni-Bug II Self-Guided Cutting System. The Uni-Bug II will carry a torch into very tight area or around very tight curves without the use of a track. Can cut straight line or radii as small as 6”. Variable speed travel from 4 to 75 ipm. Designed to run on the edge of a bar or stiffener up to 2” thick. 120 volt. Serial #0620900. Good Condition

CM901026 Bug-O DC Speed Weaving Welding Kit. Kit Includes 1 each of the following : DC-IV variable speed carriage, Speed Weaver II, Weaver swivel mount, cable mounting assembly, 93.5” rigid rail w/ magnet assemblies and 46.5” rigid rail w/ magnet assemblies. 120 volt. Serial #3737-50/3734-50 Good Condition

CM808014 Koike Model KHC-600D Portable Pipe Oxy/Fuel Hole Cutting Machine. 3.5” to 23” hole cutting diameter range. 0-4” rise and fall torch lift. Rotating gas manifold. Can be used to cut holes in pipe, vessels or flat plate. Includes cutting torch. 115 volt. Serial #053811.Purchased NEW in June, 2007 – NEVER USED

CM808015 Koike Model KHC-600D Portable Pipe Oxy/Fuel Hole Cutting Machine. 3.5” to 23” hole cutting diameter range. 0-4” rise and fall torch lift. Rotating gas manifold. Can be used to cut holes in pipe, vessels or flat plate. 115 volt. Includes cutting torch. Serial #053815. Purchased NEW in June, 2007 – NEVER USED

1 ea CM303001 Linda Shapemaker 48" Template Cutting Machine. Magnetic Template Tracing Contour Cutter. Size Capacity is any Shape that will fit in a 48" Circle. Has a Push Button RC Control. Floor Model on "H" Base. No Torch or Cutting Equipment Included. Serial #0351-18 Good Condition

1 ea Linda "Cadet" Oxy-Fuel Portable "Hand Held" Cutting Machine with Circle Attachment

1 ea Bug-O, Speed Weaver , with Two motion Torch Holder , 18" Rack, Fits All clamp. Mounted on Floor Stand. Very Good Condition

1 ea Bug-O, "Con-O" 5, Contour Saddle Cutter. Ser.# 8961 For Cutting and Beveling saddle holes in pipe. Capacity 18" to 30" diameter holes. Complete with Torch

H & M Pipe Beveling Machines!! From 2" diameter pipe to 36". All Machines are complete. We Have Both Motorized and Hand Crank Units. CALL FOR PRICES

1 ea FAB701006 Whitney 4" x 4" x 3/16" Hydraulic Angle Iron Shear. Shear with hydraulic cylinder mounted in a bench mount frame. Hydraulic pump NOT included. Serial # N/A Good Condition

1 ea ME408007 Gullco Plate Beveller Model BCM-12. 5/8" Capacity. Mounted on Roller Base Stand. 230/460 volt. 3-phase. Serial #71382-1 Good Condition

1 ea FAB611011P Comaca Model N225 Uninotch Universal Notcher. 8.5" x 8.5" x 1.56" Capacity. Equipped with T-Slotted Cast Table, Pneumatic Gauges, Automatic Feed, Swing Down Blade Guard, Remote Foot Switch, Hydraulic Pump Motor and Electric and Air Controls. Serial #N/A Good Condition

ME903010 Diamond Ground Products Piranha III Tungsten Grinder. .040 to 3/16” diameter capacity. 10 degree to 60 degree bevel capacity. 120 volt. Serial #P3-0402263-R1 Good Condition

1 ea VC802003P Airline Model VC-48 Vacuum Chamber. 48" diameter x 24" high welding chamber. 38" high work table. 2 sets of vacuum glove ports. Includes a vacuum pump, vacuum gauge and inert gas flow-meter with pressure regulator. Serial #193 Good Condition

1 ea VC704016 Jetline Model VC-48Z Vacuum Welding Chamber. Chamber is 48" diameter x 24" high with a transparent domed removable top. 39" high work table. Includes 2 pair of 8" diameter glove ports, vacuum pump, vacuum gauge, inert gas flowmeter with pressure gauge. Serial #900441 Excellent Condition

1 ea VC701002 Vacuum Atmospheres Corporation Model HE-233-62 Vacuum Chamber. 96" long x 42" wide x 32" high vacuum / welding chamber. 39" high work table. 5 glove ports on both sides of the 8’ length. Includes a Vacuum Atmospheres Corp. Model HE-373-BIN (Serial #50517-464) 300 degree, 800 watt drying furnace. Serial #20922-1 Good Condition

1 ea ME702001 Elmatco Degaussatron Dual Loop Demagnitizer. Complete dual coil demagnetizing system that includes a model VCFNR50 Control, 2 each model L1S6-24X24 coils, 2 each support cradles and track. 208/230/380/415/460 volt 1-phase. Serial #9065521X,9065551X & 9065550X Very Good Condition.

1 ea ME704010 Arc-Air Model N-6000 Automatic Gouging System. 1600 amp capacity. Accepts gouging electrodes from 5/16" to ¾" diameter. System includes torch head, automatic controller, 1600 amp contactor, power cable assembly and interconnecting cable assembly. Requires 60 to 100 psi compressed air (45 to 80 cfm). 120 volt. Serial #1237 Very Good Condition

1 ea FAB611006P 36" x 58" Scissor Lift Table. Equipped with casters for ease of movement. Good Condition

1 ea ME611016 Torit / Donaldson Mini Trunk 2 gun fume exhaust system. 150cfm nominal air flow. 6.7HP motor. 460 volt, 3-phase. Serial #IGS88000-2 Good Condition

1 ea ME611008P Aerocology Model CFP-1500F Portable Dust Collector. 18.75" wide x 42" deep x 6’5" high on floor mount casters. 3HP motor. Equipped with two cartridge filters, air blast cleaning and dust drawers. 460 volt, 3-phase. Serial #43920 Good Condition

1 ea WE301001 Linda Twin Wire Overlay Head. Linda Twin Wire Feed Head with 90 Degree 48" Contact Tube Assembly and 2" Mechanical Weld Oscillator. Used for External Overlay or Internal Overlay of Cylinders Over 12" I.D. Good Condition $ 1,950.

1 ea ME209009 GE Type MC-6A Power DC Circuit Breaker. 750 Volt. 12,000 Amp. Manual Operated. Serial #196A1956-90-GB Very Good Condition $ 8,950.

1 ea ME205001 Thermco Model 6205CA30A1100 Gas Mixer. 0 - 30% CO2 in Argon. Capacity of 0 - 5000 PSIG. 100 - 125 PSIG Inlet Pressure. 10 - 50 PSIG Outlet Pressure. 60 Gallon Surge Tank. With Gas Analyzer and Optional Alarm System. 115 Volt. Serial #18381 Excellent Condition!

1 ea ELL RJPP&CS Elliot "Root Jet" Power Pipe & Tube Cleaning System. Complete with Air Drive Motors and Cleaning Heads for 2.5" thru 14" Pipe. Complete with Spares

1 ea OMA AFFRI Affri by O.M.A.G. Portable Hand Held Hardness Tester. Carrying Case and Test Piece. Very Easy to Use! Excellent Condition

Welding Positioning Equipment

Welding Positioners, Column Boom Weld Head Manipulators, Tank Turning Rolls, Weld Seamer, Seam Welders, Indexing Turntables, Headstocks, Lathes, Rotators, Pipe Gripper Chucks, Used Orbital Welders, Automated Longitudinal and Circumferential Welding Systems.

Newest Inventory of Used Welding Equipment Arrival!!

NEW POSITIONERS & CHUCKS